Velkommen til portalen for nye arbejdsemner

3469 Hits

ISO/TC 163/SC 3/WG 12

  • prEN 14325 rev

    10-02-2016
    00162309

    Protective clothing against chemicals - Test methods and performance classification of chemical protective clothing materials, seams, joins and assemblages

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the performance classification and test methods for materials used in chemical protective clothing, including gloves and including footwear, when the footwear is an integral part of the clothing, and for seams, joins and assemblages. This is a reference standard to which chemical protective clothing performance standards may refer in whole or in part, but this standard is not exhaustive in the sense that product standards may well require testing according to test method standards which are not included in this standard. For some of the test method standards for chemical protective clothing referenced in this European Standard, this European Standard modifies the requirements for conditioning, sampling, calculation of test results and reporting. At these instances this standard takes precedence over the referenced test method standards. NOTE Whilst these performance levels are intended to relate to the usage to which the chemical protective clothing is to be put, it is essential that the chemical protective clothing manufacturer or supplier indicate the intended use of the protective clothing and that the user (specifier) carries out a risk assessment in order to establish the correct performance level for the intended task. This should be included as a mandatory requirement in the information to be supplied by the manufacturer in the product standard.
  • prEN ISO 14329 rev

    15-06-2012
    00121634

    Resistance welding - Destructive tests of welds - Failure types and geometric measurements for resistance spot, seam and projection welds

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN 14351-1 rev

    22-04-2011
    00033431

    Windows and doors - Product standard, performance characteristics - Part 1: Windows and external pedestrian doorsets without resistance to fire and/or smoke leakage characteristics

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Komite
    Beskrivelse
    This European Standard identifies material independent performance characteristics that are applicable to windows (including roof windows, roof windows with external fire resistance and French windows), external pedestrian doorsets (including unframed glass doorsets, escape route doorsets) and screens. This European Standard applies to: Manually or power operated windows, French windows and screens for installation in vertical wall apertures and roof windows for installation in inclined roofs, complete with: - related hardware, if any; - weather stripping, if any; - glazed apertures when intended to have glazed apertures; - with or without incorporated shutters and/or shutterboxes and/or blinds; and manually or power operated windows, roof windows, French windows and screens that are - fully or partially glazed including any non-transparent infill; - fixed or partly fixed or openable with one or more casements/sashes (e.g. hinged, projecting, pivoted, sliding). - Manually operated external pedestrian doorsets with flush or panelled leaves, complete with: - integral fanlights, if any; - adjacent parts that are contained within a single frame for inclusion in a single aperture, if any. The products covered by this European Standard are not assessed for structural applications. This European Standard does not apply to: - windows and pedestrian doorsets subject to regulations on smoke leakage and resistance to fire according to prEN 16034 but individual characteristics and performance requirements given in clause 4 can be relevant for these doors and windows (see prEN 16034); - rooflights according to EN 1873 and prEN 14963; - curtain walling according to EN 13830; - industrial, commercial and garage doors and gates according to EN 13241-1; - internal pedestrian doorsets according to prEN 14351-2 but individual characteristics and performance requirements given in clause 4 can be relevant for internal doors (see prEN 14351-2); - revolving doorsets;
  • EN 14351-1:2006+A1:2010/prA2

    06-10-2015
    00033510

    Windows and doors - Product standard, performance characteristics - Part 1: Windows and external pedestrian doorsets without resistance to fire and/or smoke leakage characteristics

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard identifies material independent performance characteristics that are applicable to win-dows (including roof windows, roof windows with external fire resistance and French windows), external pedestrian doorsets (including unframed glass doorsets, escape route doorsets) and screens. This European Standard applies to: - Manually or power operated windows, French windows and screens for installation in vertical wall aper-tures and roof windows for installation in inclined roofs, complete with: - related hardware, if any; - weather stripping, if any; - glazed apertures when intended to have glazed apertures; - with or without incorporated shutters and/or shutterboxes and/or blinds; and manually or power operated windows, roof windows, French windows and screens that are - fully or partially glazed including any non-transparent infill; - fixed or partly fixed or openable with one or more casements/sashes (e.g. hinged, projecting, pivoted, sliding). - Manually operated external pedestrian doorsets with flush or panelled leaves, complete with: - integral fanlights, if any; - adjacent parts that are contained within a single frame for inclusion in a single aperture, if any. The products covered by this European Standard are not assessed for structural applications. This European Standard does not apply to: - windows and pedestrian doorsets subject to regulations on smoke leakage and resistance to fire according to prEN 14351-3 but individual characteristics and performance requirements given in clause 4 can be relevant for these doors and windows (see prEN 14351-3); - rooflights according to EN 1873 and prEN 14963; - curtain walling according to EN 13830; - industrial, commercial and garage doors and gates according to EN 13241-1; - internal pedestrian doorsets according to prEN 14351-2 but individual characteristics and performance re-quirements given in clause 4 can be relevant for internal doors (see prEN 14351-2); - revolvin
  • EN 14364:2013/prA1

    11-07-2014
    00155819

    Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage, including culverts, with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together. It is the responsibility of the purchaser or specifier to make the appropriate selections taking into account their particular requirements and any relevant national regulations and installation practices or codes. This European Standard is applicable to GRP-UP, with flexible or rigid joints (see 3.33 and 3.34), primarily intended for use in buried installations. It is applicable to pipes, fittings and their joints of nominal sizes from DN 100 to DN 4000, which are intended to be used for the conveyance of surface water or sewage at temperatures up to 50 °C, with or without pressure. This European Standard covers a range of nominal sizes, nominal stiffnesses and nominal pressures. Clause 6 is applicable to fittings made using any of the following techniques: a) fabricated from straight pipe; b) moulded by: 1) filament winding; 2) tape winding; 3) contact moulding; 4) hot or cold press moulding. This European standard is applicable to the joints to be used in GRP-UP piping systems to be used for the conveyance of water, both buried and non-buried. It is applicable to joints, which are or are not intended to be resistant to axial loading. It covers requirements to prove the design of the joint. It specifies type test performance requirements for the following joints as a function of the declared nominal pressure rating of the pipeline or system: c) socket-and-spigot (either integral with pipe or sleeve coupling) or mechanical joint; d) locked socket-and-spigot joint; e) cemented or wrapped joint; f) bolted flange joint. Recommended practices for the installation of bur ...
  • prEN 14373 rev

    09-11-2010
    00305126

    Explosion suppression systems

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard describes basic requirements for the design and application of explosion suppression systems. It also specifies a method for evaluating the effectiveness and the scale up of explosion suppression systems against defined explosions. The standard gives criteria for alternative test apparatus used to undertake explosion suppression efficacy tests and criteria to be applied in defining the safe operating regime of an explosion suppression system.
  • prEN 14374 rev

    20-10-2015
    00124137

    Timber structures - Laminated veneer lumber (LVL) - Requirements

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard sets out provisions regarding the performance characteristics of structural laminated veneer lumber (LVL) for use in buildings and bridges and non-structural laminated veneer lumber for internal and external applications in construction. It also lays down procedures for Assessment and Verification of Constancy of Performance of laminated veneer lumber. This European standard defines provisions for bonding strength and durability of bonding strength in dry, humid and exterior conditions. It covers structural LVL to be used in all conditions and non-structural LVL to be used in the respective conditions for which bonding strength tests have been performed.
  • prEN 14396 rev

    30-11-2012
    00165261

    Fixed ladders for manholes

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This standard applies to permanently fixed ladders in manholes. It specifies the performance criteria for the mechanical stability and resistance providing protection against falling. The ladders specified in this European Standard are suitable for use in sewage, rainwater, surface water and, subject to the requirements of national regulations, potable water environments.
  • EN 14399-1:2015/prA1

    22-02-2016
    00185377

    High-strength structural bolting assemblies for preloading - Part 1: General requirements

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the general requirements for bolt/nut/washer(s) assemblies for high-strength structural bolting, which are suitable for preloading. The intended use of bolting assemblies in accordance with this European Standard is structural metallic works. NOTE 1 – High-strength structural bolting assemblies in accordance with EN 14399-2 to EN 14399-10 are designed to fulfil the requirements of this European Standard. NOTE 2 – High-strength structural bolting assemblies are suitable for preloading in accordance with EN 1090-2 in steel structures. High-strength structural bolting assemblies smaller than M12 are not designed to be preloaded. High-strength structural bolting assemblies are not designed to be welded. Railway rail fasteners are not covered by this standard.
  • EN 14399-2:2015/prA1

    22-02-2016
    00185375

    High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the technical requirements for high-strength structural bolting assemblies in order to ensure the suitability for preloading of bolted connections in metallic structures. A suitability test is specified to check the behaviour of the structural bolting assemblies so as to ensure that the required preload can be reliably obtained by the tightening methods specified in EN 1090 2 with sufficient margins against overtightening and against failure.
  • prEN 14404 rev

    30-10-2009
    00162316

    Personal protective equipment - Knee protectors for work in the kneeling position

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies requirements and test methods for knee protectors for work in the kneeling position
  • EN ISO 14405-2:2011/prA1

    28-02-2017
    00290227

    Geometrical product specifications (GPS) – Dimensional tolerancing – Part 2: Dimensions other than linear sizes – Amendment 1

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 14414 rev

    29-08-2016
    00197093

    Pump system energy assessment

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 14456 rev

    17-06-2014
    00164580

    Products used for treatment of water intended for human consumption - Bone charcoal

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard is applicable to bone charcoal used for the treatment of water intended for human consumption. It describes the characteristics of bone charcoal and specifies the requirements and the corresponding test methods for bone charcoal. It gives information on its use in water treatment.
  • prEN ISO 14457 rev

    19-07-2014
    00055386

    Dentistry - Handpieces and motors

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 14458 rev

    02-04-2015
    00085080

    Personal eye-equipment - Faceshields and visors for use with firefighters' and high performance industrial safety helmets used by firefighters, ambulance and emergency services

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
    Beskrivelse
    This document applies to visors designed specifically to be fitted to and/or used with helmets conforming to EN 443 when used by firefighters, or helmets which conform to EN 443 or prEN 14052 when used by ambulance and emergency services, as the situation dictates. They are intended to provide protection against the various hazards expected to be encountered in firefighting, ambulance and emergency service duties, except respiratory, smoke, and gas /vapour hazards.
  • prEN 14460 rev

    04-12-2014
    00305125

    Explosion resistant equipment

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard specifies requirements for explosion pressure resistant and explosion pressure shock-resistant equipment. This standard is applicable to process vessels and systems. It is not applicable to individual items of equipment such as motors and gearboxes that may be designed to withstand an internal explosion, which are subject of EN 13463-3. This standard is valid for atmospheres having pressures ranging from 800 hPa to 1100 hPa and temperatures ranging from -20 °C to +60 °C. This standard applies to equipment and combinations of equipment where deflagrations may occur and is not applicable to equipment and combination of equipment where detonation may occur. It is essential that this standard be used for equipment made of metallic materials only.
  • prEN 14492-2 rev

    09-11-2012
    00147129

    Cranes - power driven winches & hoists - Part 2: Power driven hoists

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    EN 14492-2:2006+A1:2009 shall be reviewed on the basis of EN 13135 and EN 13001- 1, 2 and -3.1.
  • ISO/NP TR 14521

    13-11-2015
    070392

    Gears -- Calculation of load capacity of wormgears

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN 14525 rev

    21-08-2009
    00203042

    Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials : ductile iron, grey steel, PVC-U, PE, fibre-cement

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies the requirements and associated test methods applicable to wide tolerance ductile iron couplings and wide tolerance flange adaptors intended for use with pipe components made from a number of pipe materials (ductile iron, grey iron, PE, PVC-U, steel, fibre-cement), for providing a leak tight seal over a wide range of pipe external diameters: - to convey water (e.g. potable water); - with or without pressure; - to be installed below or above ground, inside or outside buildings. This standard is not intended to cover sewerage or gas applications, where other requirements may be necessary. This standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron products. This standard covers ductile iron products cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, in a size range extending from DN 40 to DN 600, for an allowable operating pressure (PFA) up to 16 bar, for fluid temperatures between 0 °C and 25 °C excluding frost. For higher temperatures, up to 50 °C, additional type testing should be carried out. It also gives performance requirements and associated test methods for restrained and non-restrained flexible joints. Joint design and gasket shapes are outside the scope of this standard. NOTE 1 – PFA may be limited depending on pipe materials effectively connected. NOTE 2 – In this standard, all pressures are relative gauge pressures, expressed in bars (100 kPa = 1 bar). NOTE 3 – EN 545 gives the specifications for the ductile iron fittings to be used with ductile iron pipes. NOTE 4 – EN 12842 gives the specifications for the ductile iron fittings to be used with PVC-U and PE pipes.
  • prEN ISO 14532

    18-09-2015
    00238012

    Natural gas - Vocabulary

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
    Beskrivelse
    This International Standard establishes the terms, definitions, symbols, and abbreviations used in the field of natural gas. The terms and definitions have been reviewed and studied in order to cover all aspects of any particular term with input from other sources such as European Standards from CEN (The European Committee for Standardization), national standards, and existing definitions in the IGU Dictionary of the Gas Industry. The definitive intention of this document is to incorporate the reviewed definitions into the ISO/TC 193 source standards.
  • prEN ISO 14555 rev

    18-12-2015
    00121744

    Welding - Arc stud welding of metallic materials

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 14575 rev

    26-11-2015
    00189223

    Geosynthetics - Test method for determining the resistance of polymeric geosynthetic barriers to environmental stress cracking

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies a test method for screening the resistance of polymeric geosynthetic barriers to stress cracking. The test is applicable to polypropylene and polyethylene based products and to all other polymeric geosynthetic barriers which have a partially crystalline structure. The data are suitable for screening and determination of conformity but not for deriving performance data such as lifetime, unless supported by further evidence.
  • prEN 14585-1 rev

    04-04-2008
    00342014

    Corrugated metal hose assemblies for pressure applications - Part 1: Requirements

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Komite
    Beskrivelse
    This European Standard specifies the requirements for material, design, manufacturing, testing and documentation for corrugated metal hose assemblies for pressure applications for use with a maximum allowable pressure PS greater than 0,5 bar.
  • prCEN/TR 14585-2 rev

    04-04-2008
    00342015

    Corrugated metal hose assemblies for pressure applications - Part 2: Guidance on the use of conformity assessment procedures

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Komite
    Beskrivelse
    This Technical Report gives guidance for: the implementation of EN 14585-1 by proposing a procedure to place these pressure hose assemblies on the market; appropriate conformity assessment procedures as described in the annex III of the EU Directive 97/23/EC for Pressure Equipment [1].