Velkommen til portalen for nye arbejdsemner

3480 Hits

ISO/TC 69/SC 4/WG 11

  • prEN ISO 15952 rev

    05-11-2015
    00345085

    Soil quality - Effects of pollutants on juvenile land snails (Helicidae) - Determination of the effects on growth by soil contamination

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN 15969-1 rev

    04-11-2015
    00296087

    Tanks for transport of dangerous goods - Digital interface for the data transfer between tank vehicle and with stationary facilities - Part 1: Protocol specification - Control, measurement and event data

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies data protocols and data format for the interfaces between electronic equipment (TVE), on-board computer (OBC) of the tank vehicle and stationary equipment for all interconnecting communication paths. This European Standard specifies the basic protocol FTL used in the communication (basic protocol layer), the format and structure of FTL-data to be transmitted (data protocol layer) and describes the content of the FTL-data. This data protocol may be used for other application, e.g. between stationary tank equipment and offices.
  • prEN 15969-2 rev

    04-11-2015
    00296086

    Tanks for transport of dangerous goods - Digital interface for the data transfer between tank vehicle and with stationary facilities - Part 2: Commercial and logistic data

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the data structure needed for tour management, scheduling orders of measured and unmeasured products online to the truck. Processed orders are transferred back to the host in the office at once or later every time the truck is online. It specifies the transfer of commercial and logistic data between transport vehicle equipment, on board computer of the tank vehicle and stationary facilities for all communication channels between these parties.
  • prEN ISO 15995 rev

    05-02-2015
    00286169

    Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 15996 rev

    25-02-2014
    00023184

    Gas cylinders - Residual pressure valves - General requirements and type testing (ISO 15996:2005)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    ISO 15996:2005 specifies requirements for residual pressure valves, with or without a non-return function, for gas cylinders and the methods of testing such valves, for type approval. ISO 15996:2005 is applicable to valves to be fitted to gas cylinders of up to 150 l water capacity, intended to contain compressed, liquefied or dissolved gases. ISO 15996:2005 does not cover valves for fire extinguishers, cryogenic equipment or liquefied petroleum gas.
  • prEN 15999-2

    15-04-2011
    00346036

    Conservation of cultural property - Guidelines for management of environmental conditions - Recommendation for showcases used for exhibition and preservation of cultural heritage - Part 2: Technical requirements

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
  • prEN ISO 16001

    14-10-2015
    00151454

    Earth-moving machinery - Hazard detection systems and visual aids - Performance requirements and tests

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This International Standard specifies general requirements and describes methods for evaluating and testing the performance of object detection systems (ODS) and visibility aids (VA) used on earth-moving machines. It covers the following aspects: - detection and/or visibility of objects including people in the detection zone; - visual, audible, or both warnings to the operator and if appropriate to the persons in the detection zone; - operational reliability of the system; - compatibility and environmental specifications of the system. It is applicable to machines as defined in ISO 6165. ODS, VA or both can be used to augment the operator‘s direct vision (see ISO 5006) or indirect vision using mirrors (see ISO 14401) or to provide additional means of object detection, for example, where ergonomic considerations limit the effectiveness of direct vision and to avoid repeated turning of the head and upper body.
  • prEN 16002 rev

    11-06-2015
    00254163

    Flexible sheets for waterproofing - Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies a test method to determine the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing. The assessment is limited to the performance of the mechanically fastened flexible sheets only. The test method does not include the determination of the performance of the mechanical fastener and/or the combination of the mechanical fastener and the substrate.
  • prEN ISO 16050 rev

    17-04-2018
    00275344

    Foodstuffs -- Determination of aflatoxin B1, and the total content of aflatoxins B1, B2, G1 and G2 in cereals, nuts and derived products -- High-performance liquid chromatographic method

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 16054 rev

    30-09-2015
    00285126

    Implants for surgery - Minimum data sets for surgical implants

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 16061 rev

    23-01-2009
    00285106

    Instrumentation for use in association with non-active surgical implants - General requirements

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 16072 rev

    05-08-2015
    00345082

    Soil quality -- Laboratory methods for determination of microbial soil respiration

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 16092-2

    12-10-2015
    00143089

    Machine tools safety - Presses - Part 2: Safety requirements for mechanical presses

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    1.1 This European Standard specifies technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of mechanical presses with part revolution clutch hereinafter called presses which are intended to work cold metal or material partly of cold metal. NOTE – The design of a machine includes the study of the machine itself, taking into account all phases of its “life”, i.e. construction, transport and commission (including assembly, installation and adjustment), use (including setting, teaching/programming or process changeover, operation, cleaning, fault finding and maintenance) and de-commissioning, dismantling and, as far as safety is concerned, disposal, and the drafting of the instructions related to all above-mentioned phases of the “life” of the machine (except construction), dealt with it in 6.5 of EN ISO 12100-2:2003. 1.2 This European Standard also covers presses, whose primary intended use is to work cold metal, which are to be used in the same way to work other sheet materials (such as cardboard, plastic, rubber or leather), and metal powder. 1.3 The requirements in this standard take account of intended use, as defined in 3.22 of EN ISO 12100-1:2003. This standard presumes access to the press from all directions, deals with the hazards during the various phases of the life of the machine described in clause 4, and specifies the safety measures for both the operator and other exposed persons. 1.4 This European Standard also applies to ancillary devices which are an integral part of the press. This standard also applies to machines which are integrated into an automatic production line where the hazards and risk arising are comparable to those of machines working separately. 1.5 This European Standard does not cover mechanical presses with full revolution clutch. 1.6 This European Standard does not cover machines whose principal designed purpose is: a) sheet metal cutting by guillotine; b) attaching a
  • prEN ISO 16092-4

    12-10-2015
    00143090

    Machine tools - Safety for presses - Part 4: Pneumatic presses

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    1.1 This European Standard specifies technical safety requirements and protective measures to be adopted by persons undertaking the design as defined in 3.11 of EN 292-1:1991, manufacture and supply of pneumatic presses the intended use of which is the cold working of metal or material partly of metal as defined in 3.1.13 and hereafter referred as machines. This standard also applies to machines which are integrated into an automatic production line where the hazards and risk arising are comparable to those of machines working separately. 1.2 This standard also covers pneumatic presses: - whose primary intended use is the cold working of metal, which are to be used in the same way to work other sheet materials (e.g. cardboard, plastic, rubber, leather) and metal powder; - with an intermediate pneumatic/hydraulic intensifier. 1.3 The requirements in this standard take account of intended use, as defined in 3.12 of EN 292-1:1991. This standard presumes access to the press from all directions, deals with the hazards described in clause 4, and specifies the safety measures for both the operator and other exposed persons. 1.4 This standard also applies to ancillary devices which are an integral part of the press. This standard also applies to machines which are integrated into an automatic production line where the hazards and risk arising are comparable to those of machines working separately. 1.5 This standard does not cover machines whose principal designed purpose is: a) sheet metal cutting by guillotine; b) bending or folding by pneumatic press brakes or folding machines; c) spot welding; d) tube bending; e) straightening; f) drop stamping; g) working by pneumatic hammer; h) compaction of metal powder. Special pneumatic machines for assemblying or calibrating are not covered but this standard may be used as a basis for there machines. 1.6 This standard does not cover the safety requirements related to the use of PES or PPS. They will be dealt with a
  • prEN 16102 rev

    03-04-2014
    00278377

    Intelligent transport systems - ESafety - Third party services supported eCall - Operating requirements

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    Standardisation in the field of eCall support by specifying third party services supported eCall – Operating requirements
  • prEN ISO 16119-5

    22-11-2013
    00144315

    Agricultural and forestry machinery - Environmental requirements for sprayers - Aerial application platforms

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This part of ISO 16119 specifies requirements and methods for design and performance of aerial fixed wing and rotary aircraft platforms for agriculture, forestry and human health, with respect to minimizing the risk of environmental contamination. It is intended to be used with ISO 16119-1, which gives general requirements common to all the sprayer types covered by ISO 16119. When requirements of this part of ISO 16119 are different from those which are stated in ISO 16119-1, the requirements of this part of ISO 16119 take precedence over the requirements of ISO 16119-1 for machines within the scope of this part of ISO 16119. It does not cover safety aspects (see ISO 4254-6) or required safety and design criteria for air worthiness and aircraft registration nor pilot requirements of various countries and localities.
  • EN ISO 16122-4:2015/prAC

    03-08-2015
    00144C25

    Agricultural and forestry machines - Inspection of sprayers in use - Part 4: Fixed and semi-mobile sprayers

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 16122-5

    05-10-2015
    00144345

    Agricultural and forestry machines - Inspection of sprayers in use - Part 5: Aerial spray systems - Environmental protection

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This International Standard specifies the requirements and test methods for their verification for inspection in use for aerial fixed wing and rotary aircraft spray systems for agriculture, horticulture forestry and human health, with respect to minimizing the risk of environmental. This part of ISO 16122 relates mainly to the condition of the equipment with respect to its potential risk for the environment and its performance to achieve good applications. NOTE: Requirements for the protection of inspectors during an inspection are given in ISO 16122-1.
  • prEN ISO 16133 rev

    16-12-2014
    00345077

    Soil quality - Guidance on the establishment and maintenance of monitoring programmes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 16140-3

    23-09-2014
    00275309

    EN ISO 16140-3 Microbiology of the food chain — Method validation — Part 3: Protocol for the verification of reference and alternative methods implemented in a single laboratory

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This document deals with verification of methods for the detection and/or the enumeration of microorganisms, with particular emphasis on the implementation of a reference/alternative method in the user laboratory and verification of a reference/alternative method using items included in the scope of the method and tested routinely but not tested in the original validation study
  • prEN ISO 16140-4

    23-09-2014
    00275304

    EN ISO 16140-4 Microbiology of the food chain - Method validation - Part 4: Protocol for in-house (single) laboratory method validation

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    The proposed deliverable specifies the procedure for single-laboratory validation of mainly non-proprietary methods in the fields of microbiological analysis of food, feed, and environmental and primary production stage samples. Single-laboratory validation is required if an interlaboratory validation according to ISO 16140-2 is not appropriate, e.g. for in-house methods or when the required number of participating laboratories is not available. Single-laboratory validation is not part of the optimization of methods. It can be applied only for methods that are fully specified with regard to all relevant parameters (including tolerances on temperatures and specifications on nutrient media). The proposed deliverable describes two protocols for single-laboratory validation, a conventional protocol, and a factorial protocol. The conventional protocol is a stepwise procedure; both the study design and the performance measures are derived from ISO 16140-2. The performance measures of the factorial protocol are also derived from ISO 16140-2; however, it is using an orthogonal, factorial study design. By selection of suitable influencing factors (technician, nutrient media, sample preparation, temperature, duration) a high certainty of the determined method validation parameters is obtained, so that the number of required individual tests can be reduced by more than 50 %.
  • prEN ISO 16140-5

    23-09-2014
    00275310

    EN ISO 16140-5 Microbiology of the food chain — Method validation — Part 5: Protocol for factorial interlaboratory method validation

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    The proposed deliverable specifies an alternative technical protocol for the validation of mostly non-proprietary methods in the field of microbiological analysis of food, animal feed, and environmental and primary production stage samples. It is closely related to ISO 16140-2. The latter specifies the technical protocol for the validation of proprietary methods, including a classical interlaboratory study and a method comparison study to be conducted in one laboratory. The realization of classical interlaboratory studies demands a sufficient number of participating laboratories (at least 8 laboratories are required). There are many occasions where a sufficient number of participating laboratories is not available (e.g. when a new method is required quickly after an outbreak of a new microorganism). In this case, the validation cannot be considered as reliable any longer. The proposed deliverable uses a modified protocol based on orthogonal, factorial studies. By selection of suitable influencing factors (technician, nutrient media, sample preparation, temperature, duration) a high certainty of the determined method validation parameters is obtained, so that the number of required collaborating laboratories can be reduced up to a minimum of 4. This validation protocol can be used in different ways. If the 4 collaborators can be considered a “random sample” of independent and competent laboratories and from different organizations, the test method can be considered as being validated in the sense that accurate and precise measurements are to be expected from any competent laboratory. If the 4 collaborators can be considered a “random sample” of independent and competent laboratories from one organization, the test method can be considered as being validated in the sense that accurate and precise measurements are to be expected from any competent laboratory in this organization.
  • prEN ISO 16140-6

    23-09-2014
    00275305

    EN ISO 16140-6 Microbiology of the food chain — Method validation — Part 6: Protocol for the validation of microbiological confirmation methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
    Beskrivelse
    This part of ISO 16140 specifies the general principle and the technical protocol for the validation of alternative, mostly proprietary, confirmation methods in the field of microbiological analysis of food, animal feed, and environmental and primary production stage samples. This procedure is limited to the validation of alternative (proprietary) confirmation methods that are intended to replace (partly or completely) the confirmatory procedure described in the standard method for the enumeration or detection of specific (group of) microorganisms. The "sample" to be used for confirmation shall be a suspected colony that has been obtained following the reference or alternative culture method procedure. It is however not intended for confirmation using a (pure) colony from an unknown origin. Validation studies according to this standard are intended to be performed by organizations involved in method validation.
  • prEN ISO 16147 rev

    04-12-2015
    CST01146

    Small craft - Inboard diesel engines - Engine-mounted fuel and electrical components

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 16156

    01-09-2006
    00143045

    Machine-tools safety - Safety requirements for the design and construction of work holding chucks

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Komite
    Beskrivelse
    This European Standard sets out the requirements and/or measures to remove the hazards and limit the risk on work holding chucks which are defined in 3.1. It covers all the hazards relevant to this component, as listed in Clause 4. The requirements concern designers, manufacturers, suppliers and importers of work holding chucks. It also includes information which the manufacturer shall provide for the user.