Velkommen til portalen for nye arbejdsemner

3474 Hits

ISO/TC 69/SC 4/WG 11

  • prEN ISO 20815 rev

    29-01-2016
    00012359

    Petroleum, petrochemical and natural gas industries - Production assurance and reliability management

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 20823 rev

    14-06-2016
    00019514

    Petroleum and related products – Determination of the flammability characteristics of fluids in contact with hot surfaces – Manifold ignition test

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 20848-3 rev

    24-11-2015
    00261440

    Packaging -- Plastics drums -- Part 3: Plug/bung closure systems for plastics drums with a nominal capacity of 113,6 l to 220 l

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 20866

    05-12-2014
    00309180

    Footwear - Test methods for insoles - Delamination resistance

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This international standard specifies a test method for the determination of the delamination resistance of insoles, irrespective of the material
  • prEN ISO 20867

    02-12-2014
    00309179

    Footwear - Test methods for insoles - Heel pin holding strength

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    TThis international standard specifies a method to determine the ability of an insole component to hold a heel pin and to prevent its head from being pulled through the insole component. The method is applicable to insoles used in the seat of footwear with inside attached heels, and also to seat components where outside heel attachments are used and the heel pin is clenched
  • prEN ISO 20870

    02-12-2014
    00309177

    Footwear -- Ageing conditioning

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard specifies laboratory procedures which are intended to imitate the effects of naturally occurring reactions. The physical properties of interest are measured before and after the application of the specified treatments. The effect of the ageing procedures on any of the physical properties of the material may be examined
  • prEN ISO 20871

    05-12-2014
    00309184

    Footwear - Test methods for outsoles - Abrasion resistance

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This International standard specifies a method for the determination of the abrasion resistance for outsoles, irrespective of the material
  • prEN ISO 20872

    05-12-2014
    00309185

    Footwear - Test methods for outsoles - Tear strength

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This International standard specifies a method for the determination of the tear strength of outsoles, irrespective of the material, using trouser test pieces
  • prEN ISO 20873

    05-12-2014
    00309181

    Footwear - Test methods for outsoles - Dimensional stability

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This international standard specifies a method for determining the linear shrinkage after heating of test specimens prepared from outsoles.
  • prEN ISO 20874

    02-12-2014
    00309178

    Footwear - Test methods for outsoles - Needle tear strength

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This International standard specifies a method for the determination of the needle tear strength of outsoles, irrespective of the material.
  • prEN ISO 20875

    05-12-2014
    00309188

    Footwear - Test methods for outsoles - Determination of split tear strength and delamination resistance

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This international standard specifies a method for the determination of the split tear strength and delamination resistance for outsoles
  • prEN ISO 20876

    05-12-2014
    00309187

    Footwear - Test methods for insoles - Resistance to stitch tear

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This international standard describes a method for evaluating the ability of an insole, irrespective of the material, to hold stitches, or to take clenched metal fastenings. The method has become accepted as a general quality criterion for insole materials even where attachment is by means of adhesives
  • prCEN ISO/TR 20879 rev

    07-02-2019
    00309208

    Footwear – Performance requirements for components for footwear – Uppers

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prCEN ISO/TR 20880 rev

    07-02-2019
    00309209

    Footwear – Performance requirements for components for footwear – Outsoles

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prCEN ISO/TR 20881 rev

    07-02-2019
    00309210

    Footwear – Performance requirements for components for footwear – Insoles

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prCEN ISO/TR 20882 rev

    07-02-2019
    00309211

    Footwear – Performance requirements for components for footwear – Lining and insocks

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prCEN ISO/TR 20883 rev

    07-02-2019
    00309212

    Footwear – Performance requirements for components for footwear – Shanks

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 20957-2

    16-01-2017
    00136406

    Stationary training equipment – Part 2: Strength training equipment, additional specific safety requirements and test methods

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    ISO 20957-2:2005 specifies additional safety requirements for strength training equipment in addition to the general safety requirements of ISO 20957-1:2005. ISO 20957-2:2005 is applicable to stationary training equipment type strength training equipment with stack weight resistance or other means of resistance like weight discs, elastic cords, hydraulic, pneumatic and magnetic systems and springs (type 2) with the classes S and H.
  • prEN ISO 20957-7

    16-01-2017
    00136407

    Stationary training equipment – Part 7: Rowing machines, additional specific safety requirements and test methods

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    ISO 20957-7:2005 specifies safety requirements for rowing machines in addition to the general safety requirements of ISO 20957-1 and should be read in conjunction with it. ISO 20957-7:2005 is applicable to stationary training equipment type rowing machines (type 7), referred to as rowing machines, within the classes S and H and class A regarding accuracy. If accessories are provided with the rowing machine for the performance of additional exercises these are subject to the requirements of ISO 20957-1 and any other specific requirements of the appropriate part of this standard.
  • prEN ISO 21012

    13-11-2013
    00268058

    Cryogenic vessels - Hoses

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard gives design, construction, type and production testing, and marking requirements for non insulated cryogenic flexible hose used for the transfer of cryogenic fluids within the following range of operating conditions : – working temperature: from – 270 °C to + 65 °C ; – maximum nominal pressure: 80 bar ; – nominal size (DN): from 10 to 100. End fittings for mounting of any couplings are within the scope of this standard, but the couplings are subject to other standards. It is intended that the hose be designed and tested to satisfy the generally accepted nominal pressure e.g. PN 40. Hoses may then be selected with a PN equal to or greater than the maximum allowable pressure (PS) of the equipment to which it is to be used.
  • prCEN ISO/TS 21176

    07-12-2016
    00278437

    Intelligent transport systems – Cooperative ITS – Position, velocity and time functionality in the ITS station

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 21183-2 rev

    11-12-2015
    00188098

    Light conveyor belts - Part 2: List of equivalent terms

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prCEN ISO/TS 21184

    07-12-2016
    00278439

    Intelligent transport systems – Secure vehicle interface – Data dictionary of vehicle-based information for C-ITS applications

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prCEN ISO/TS 21185

    07-12-2016
    00278440

    Intelligent transport systems – Secure vehicle interface – Communication profiles for secure connection between an ITS-station and a vehicle

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 21254-1 rev

    27-01-2016
    00123096

    Lasers and laser-related equipment - Test methods for laser-induced damage threshold - Part 1: Definitions and general principles

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite