Velkommen til portalen for nye arbejdsemner

3474 Hits

ISO/TC 69/SC 4/WG 11

  • prEN 474-9 rev

    04-02-2015
    00151441

    Earth-moving machinery - Safety - Part 9: Requirements for pipelayers

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to pipelayers as defined in EN ISO 6165:2006, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). The requirements of this part are complementary to the common requirements formulated in EN 474-1:2006. This part does not repeat the requirements from EN 474-1:2006, but adds or replaces the requirements for application for pipelayers. This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situations and events during commissioning, operation and maintenance of pipelayers. This part specifies additional requirements for rear mounted winches. Pipelayers with rotating upper structure are excluded from the scope of this document. However, specific requirements are under development. This European Standard is not applicable to pipelayers manufactured before the date of publication of this European Standard by CEN.
  • prEN 527-3 rev

    28-03-2008
    00207197

    Office furniture - Work tables and desks - Part 3: Methods of test for the determination of the stability and the mechanical strength of the structure

    Oprindelse:
    CEN
    International kategori
    Emner
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This part of EN 527 specifies methods of test for the determination of the stability and the mechanical strength ofthe structure of office work tables and desks. NOTE – In this standard, the words « table » and « desk » have the same meaning. For simplicity, only the word « table » is used in the remainder of the standard. The tests are designed to be applied to an article of furniture that is fully assembled and ready for use.
  • prEN ISO 527-3 rev

    24-11-2015
    00249933

    Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 542 rev

    13-07-2013
    00307150

    Oilseeds - Sampling (ISO 542:1990)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 549 rev

    09-07-2015
    00208022

    Rubber materials for seals and diaphragms for gas appliances and gas equipment

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 560 rev

    27-01-2016
    00121748

    Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard lays down the dimensions and specifies the characteristics of the constituent parts of hose connections for welding, cutting and allied processes, for example for pressure regulators according to EN ISO 2503 and blowpipes. This European Standard does not cover the design of the part of the hose tail inserted into the hose. This is specified in EN 1256.
  • prEN 589 rev

    15-09-2015
    00019503

    Automotive fuels - LPG - Requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies requirements and test methods for marketed and delivered automotive LPG (Liquefied Petroleum Gas). It is applicable to automotive LPG for use in LPG engine vehicles designed to run on automotive LPG. This revision concerns lowering the sulfur limit levels, inclusion of EN 16423 and updating towards revised versions of EN 15470 and EN 15471. LPG is a highly volatile hydrocarbon liquid which is normally stored under pressure. If the pressure is released large volumes of gas will be produced which form flammable mixtures with air over the range of approximately 2 % (V/V) to 10 % (V/V). This European Standard involves the sampling, handling and testing of LPG. All procedures should be conducted away from sources of ignition such as naked flames, unprotected electrical equipment and electrostatic hazards. Testing should be performed as far as practicable under an electrically-safe ventilation hood. LPG in liquid form can cause cold burns to the skin. Protective clothing such as gloves and goggles should be worn if contact with the skin is likely to occur. Unnecessary inhalation of LPG vapour should be avoided. The operator should not be exposed to atmospheres containing more than 1 800 mg/m3 over an 8 h time-weighted average (TWA) reference period, or more than 2 250 mg/m3 over a short term, 10 min reference period. One of the tests described in this European Standard involves the operator inhaling a mixture of air and LPG vapour. Particular attention is drawn to the cautionary statement provided in A.1, where this method is referred to.
  • EN 590:2013/prA1

    21-10-2015
    00019507

    Automotive fuels - Diesel - Requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies requirements and test methods for marketed and delivered automotive diesel fuel. It is applicable to automotive diesel fuel for use in diesel engine vehicles designed to run on automotive diesel fuel containing up to 7 %(V/V) Fatty Acid Methyl Ester. NOTE – For the purposes of this European Standard, the terms "% (m/m)" and "% (V/V)" are used to represent respectively the mass fraction and the volume fraction.
  • prEN 593 rev

    08-07-2015
    00069184

    Industrial valves - Metallic butterfly valves for general purposes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies minimum general requirements for butterfly valves having metallic bodies for use in flanged or butt welding piping systems and used for isolating, regulating or control applications. The PN and Class ranges are: - PN 2,5; PN 6; PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; - Class 150; Class 300; Class 600; Class 900. The DN range is: - DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900; DN 1 000; DN 1 100; DN 1 200; DN 1 400; DN 1500; DN 1 600; DN 1 800; DN 2 000; DN 2 200; DN 2 400; DN 2 600; DN 2 800; DN 3 000; DN 3 200; DN 3 400; DN 3 600; DN 3 800; DN 4 000. DN 750 is used only for Class 150 and Class 300. For valves subject to Pressure Equipment Directive, the product standard prEN 16668 applies together with this European Standard. For industrial process control valves, EN 1349 and EN 60534-2-1 apply together with this European Standard. For water supply application, EN 1074-1 and EN 1074-2 apply together with this European Standard.
  • prEN 598 rev

    12-05-2014
    00203048

    Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings - Requirements, test methods and quality assurance

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of drains and sewers outside buildings:  operating without pressure (gravity sewerage), or with positive or negative pressure (see Table 5);  to be installed below or above ground;  to convey surface water, domestic waste water and certain types of industrial effluents, either in separate systems or in combined systems. This European Standard applies to pipes, fittings and accessories which are:  manufactured with socketed, flanged or spigot ends;  normally delivered externally and internally coated;  suitable for continuous fluid temperatures between 0 °C excluding frost, and 45 °C for DN ≤ 200 or 35 °C for DN > 200, according to EN 476;  not intended for use in areas subject to reaction to fire regulations. NOTE 1 – This does not preclude special arrangements for the products to be used at higher temperatures. This European Standard covers pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, of a size range extending from DN 80 to DN 2000 inclusive. This European Standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this European Standard. NOTE 2 – In this European Standard, all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).
  • prEN 609-3

    30-11-2012
    00144307

    Machinery for agricultural and forestry machinery - Safety of log splitters - Part 3 : Stave splitters

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies safety requirements and their verification for the design and construction of stave splitters, designed for cutting staves from wood (?), irrespective of the nature of the power source used. In addition it specifies the type of information on safe working practices provided by the manufacturer. This standard deals with all significant hazards, hazardous situations and hazardous events relevant to wedge splitters when they are used as intended and under the conditions foreseen by the manufacturer. This standard does not deal with wedge splitters dealt with in standard EN 609-1. Environmental aspects have not been considered in this standard.
  • prEN 619 rev

    24-12-2010
    00148014

    Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of unit loads

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Komite
    Beskrivelse
    This European standard deals with the technical requirements to minimise the hazards listed in Clause 4 and Annex B. These hazards can arise during the operation and maintenance of continuous handling equipment and systems when carried out in accordance with the specifications given by the manufacturer or his authorised representative. This standard deals with safety related technical verification during commissioning. This standard applies to mechanical handling devices defined in Clause 3, singly or combined to form a conveyor system, and designed exclusively for moving unit loads continuously on a predefined route from the loading to the unloading points, possibly with varying speed or cyclically. In general, it also applies to conveyors which are built into machines or attached to machines. Safety requirements and/or measures in this standard apply to equipment used in all environments. However, additional risk assessments and safety measures need to be considered for uses in severe conditions, e.g. freezer applications, high temperatures, corrosive environments, strong magnetic fields, potentially explosive atmospheres, radioactive conditions and loads the nature of which could lead to a dangerous situation (e.g. molten metal, acids/bases, specially brittle loads, explosives) operation on ships and earthquake effects and also contact with foodstuff. Hazards during decommissioning are not covered. This European Standard deals with the technical requirements for electromagnetic compatibility (EMC). This standard does not cover hazards during decommissioning and hazards generated by noise. It also does not cover operation in environments where the electromagnetic disturbances are outside the range of those specified in EN 61000-6-2. This standard does not apply to conveying equipment and systems used underground or in public areas and to aircraft ground support equipment.
  • prEN 620 rev

    05-12-2016
    00148015

    Continuous handling equipment and systems – Safety and EMC requirements for belt conveyors for bulk materials

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European standard deals with the technical requirements to minimise the risks due to the hazards listed in clause 4, which can arise during operation and maintenance of fixed belt conveyors and systems as defined in 3.1 to 3.2.4 and designed for continuously conveying loose bulk materials from the loading point(s) to the unloading point(s). Requirements for electromagnetic compatibility are also covered. This standard applies to use in ambient air temperatures of -15_ C to + 40_ C. This standard does not cover : a) use in open cast lignite mining or use underground, such as in mines or tunnels ; b) use in public areas or for man-riding ; c) floating, dredging and ship mounted equipment ; d) conveyors requiring a high level of cleanliness for hygiene reasons, e.g. in direct contact with foodstuffs or pharmaceuticals ; e) conveyors using a moving belt with other than a continuous rubber or polymeric surface for the conveying medium ; f) transportation of the conveyor ; g) the design of the supporting structure which is not part of a conveyor (see 3.2) ; h) the effects of wind ; i) hazards resulting from handling specific hazardous materials, (e.g. explosives, radiating material) ; j) hazards resulting from contact with or inhalation of harmful fluids, gases, mists, fumes or dust ; k) biological and micro-biological (viral or bacterial) hazards ; l) hazards due to heat radiation from the materials handled ; m) hazards caused by operation in electromagnetic fields outside the range of EN 61000-6-2: 1999; n) hazards caused by operation subject to special regulations (e.g. explosive atmospheres) ; o) hazards caused by noise ; p) hazards caused by the use of ionising radiation sources ; q) hazards caused by hydraulic equipment. The safety requirements of this standard apply to equipment and systems placed on the market after the date of publication of this standard.
  • prEN 646 rev

    08-12-2015
    00172173

    Paper and board intended to come into contact with foodstuffs - Determination of colour fastness of dyed paper and board

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This document describes procedures for the testing of dyed paper and board intended to come into contact with foodstuffs. Some procedures depending on the foreseeable use of the material are given. Visual evaluation against a grey scale provides grading of the bleeding. NOTE: For samples having significant different sides, a migration can occur from one glass fibre to the other and could lead to wrong interpretation of the fastness of one side. These samples should be checked using large sampling procedure to prevent cross contamination of the glass fibre during the migration procedure. The procedure is described in annexe A. If lower limit of detection is required, this procedure could also be used.
  • prEN 648 rev

    08-12-2015
    00172174

    Paper and board intended to come into contact with foodstuffs - Determination of the fastness of fluorescent whitened paper and board

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This document describes procedures for the testing of the fastness of fluorescent whitened paper and board intended to come into contact with foodstuffs. Some procedures depending on the foreseeable use of the material are given. Visual absence of the fluorescence under UV light will be evaluated. NOTE: For samples having significant different sides, a migration can occur from one glass fibre to the other and could lead to wrong interpretation of the fastness of one side. These samples should be checked using large sampling procedure to prevent cross contamination of the glass fibre during the migration procedure. The procedure is described in annexe A. If lower limit of detection is required, this procedure could also be used.
  • prEN ISO 662 rev

    06-08-2015
    00307158

    Animal and vegetable fats and oils -- Determination of moisture and volatile matter content

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 676 rev

    24-07-2013
    CSC01053

    Spices and condiments - Botanical nomenclature

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 676 rev

    27-02-2015
    00131007

    Forced draught burners for gaseous fuels

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
    Beskrivelse
    This European Standard specifies the terminology, the general requirements for the construction and operation of forced draught gas burners and also the provision of control and safety devices, and the test procedure for these burners. This Europen Standard is applicable to — automatic gas burners with a combustion air fan (hereinafter called "burners") and gas line components, intended for use in appliances of different types, and that are operated with gaseous fuels; — pre-mixed burners and nozzle mixed burners; — single burners with a single combustion chamber; — single-fuel and dual-fuel burners when operating only on gas; — the gas function of dual-fuel burners designed to operate simultaneously on gaseous and liquid fuels, which, for the latter, the requirements of EN 267 also apply. This European Standard deals with all significant machine hazards, hazardous situations and events relevant to burners, when they are used as intended and under conditions of misuse which are reasonably foreseeable, see Annex J. This European Standard specifies the requirements to ensure the safety during commissioning, start-up, operation, shut-down and maintenance. This European Standard does not apply to burners specifically designed for use in industrial processes carried out on industrial premises. This European Standard deals also with the additional requirements for the burners in the scope with pressurised parts and /or firing pressurised bodies, see Annex K. This European Standard deals also with forced draught burners intended to be used with biogenous gaseous fuels, mixtures with line-conveyed gas and special gaseous fuels. This European Standard deals also with burners equipped to increase the total appliance efficiency; see Annex M.
  • prEN 681-1 rev

    08-12-2014
    00208021

    Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard specifies requirements for materials used in vulcanized rubber seals for: a) cold potable water supply (up to 45°C); 2) hot potable and non-potable water supply (up to 110°C); 3) drainage, sewerage and rainwater systems (continuous flow up to 45°C and intermittent flow up to 95°C). The different designations of seals specified are defined according to their type, application and requirements.
  • prEN 689 rev

    15-10-2014
    00137055

    Workplace exposure — Measurement of exposure by inhalation to chemical agents — Strategy for testing compliance with occupational exposure limit values (Revision of EN 689:1995)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
    Beskrivelse
    This European standard specifies a strategy to perform representative measurements of exposure by inhalation to chemical agents in order to demonstrate the compliance with occupational exposure limit values.
  • prEN 736-1 rev

    08-07-2015
    00069186

    Valves - Terminology - Part 1: Definition of types of valves

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard gives the denominations of valves. It has the purpose to provide a uniform and systematic terminology for all types of valves. By reasons of classification of terms clause 4 defines terms related to basic design characteristics and clause 5 defines terms related to functional characteristicsof valves.
  • prEN 746-1 rev

    23-09-2005
    00186015

    Industrial thermoprocessing equipment - Part 1: Common safety requirements for industrial thermoprocessing equipment

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Komite
  • prEN 746-3 rev

    23-09-2005
    00186017

    Industrial thermoprocessing equipment - Part 3: Safety requirements for the generation and use of atmosphere gases

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    Part 3 of EN 746 specifies safety requirements for atmosphere gas systems and their use in industrial thermo-processing equipment and associated plant, including systems for the production of atmosphere gases by reaction inside the thermo-processing equipment.
  • prEN 746-6

    24-02-2006
    00186019

    Industrial Thermoprocessing Equipment Part 6: Particular Safety Requirements for Material Melting, Remelting and Liquid Phase Maintaining Thermoprocessing Equipment

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Komite
    Beskrivelse
    Part 6 of EN 746 deals with the hazards and the risks arising from molten material in the operation of thermoprocessing equipment and gives the specific hazards and safety requirements that shall be provided by the manufacturer for material melting, remelting and liquid phase maintaining treatment, whether it is used as an independent unit or as an integrated part of a plant.
  • prEN 746-7

    24-02-2006
    00186020

    Industrial Thermoprocessing Equipment Part 7: Particular Safety Requirements for Vacuum and Overpressure Thermoprocessing Equipment

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Komite
    Beskrivelse
    Part 7 of EN 746 gives the specific hazards and safety requirements for thermal processes according to Annex A that shall be provided by the manufacturer for Vacuum Industrial Thermoprocessing Equipment with or without overpressure, whether it is used as an independent unit or as an integrated part of a plant.