Velkommen til portalen for nye arbejdsemner

3469 Hits

ISO/TC 229

  • prEN 10210-1 rev

    22-12-2011
    EC103103

    Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This part of the European Standard specifies technical delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed product. Requirements for tolerances, dimensions and sectional properties are contained in EN 10210-2.
  • EN 10216-2:2013/prA1

    03-03-2016
    EC110238

    Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel. This Part of EN 10216 may also be applied for tubes of non-circular cross section; necessary modification should be agreed at the time of enquiry and order. NOTE – Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
  • prEN 10216-5 rev

    24-02-2016
    EC110236

    Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section made of austenitic (including creep resisting steel) and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures. NOTE – Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
  • prEN 10217-7 rev

    24-02-2016
    EC110237

    Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This Part of EN 10217 specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures. NOTE – Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, pressure equipment directive, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
  • prEN ISO 10218-2 rev

    01-06-2017
    00310099

    Robots and robotic devices – Safety requirements for industrial robots – Part 2: Robot systems and integration

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 10219-1 rev

    22-12-2011
    EC103101

    Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This part of the European Standard specifies the technical delivery conditions for cold formed welded structural hollow sections of circular, square or rectangular forms and applies to structural hollow sections formed cold without subsequent heat treatment. Requirements for tolerances, dimensions and sectional properties are contained in EN 10219-2.
  • prEN 10225 rev

    20-02-2014
    EC103107

    Weldable structural steels for fixed offshore structures - Technical delivery conditions

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies requirements for weldable structural steels to be used in the fabrication of fixed offshore structures in the form of plates up to and including 150 mm thick. It also specifies sections up to 63 mm thick except for sections delivered in the as-rolled condition which are permitted up to 25 mm thick only. Seamless hollow sections up to and including 40 mm thick and high frequency electric resistance welded hollow sections up to and including 20 mm thick are specified. Greater thicknesses for sections and hollow sections may be agreed, provided the technical requirements of this European Standard are maintained. The standard is applicable to steels for offshore structures, designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping, and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. temperature. In the case of hollow sections formed from plate with the seam fusion welded, this European standard covers only the requirements of the plate material. Minimum yield strengths up to 460 MPa are specified together with low temperature impact properties at temperatures down to –40 °C. This European standard applies to material supplied ex-mill or from merchant's stock.
  • prEN ISO 10240 rev

    31-05-2016
    CST01161

    Small craft – Owner's manual (ISO 10240:2004)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 10242 rev

    24-02-2012
    EC110162

    Threaded pipe fitting in malleable cast iron

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard specifies the requirements for the design and performance of threaded pipe fittings in malleable cast iron. These fittings are for general purposes for the transmission of fluids and gases up to the limits of pressure and temperature specified in the standard. They are intended for the connection of elements threaded in accordance with EN 10226-1 and EN 10226-2, sizes â...› to 6. For use in conditions outside the pressure and temperature limits specified, reference shall be made to the manufacturer.
  • prEN ISO 10253 rev

    20-05-2014
    00230324

    Water quality - Marine algal growth inhibition test with Skeletonema costatum and Phaeodactylum tricornutum

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 10253-2 rev

    28-01-2011
    EC110206

    Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This Part of EN 10253 specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases. It specifies: - type of fittings ; - type A : Butt-welding fittings with reduced pressure factor ; - type B : Butt-welding fittings for use at full service pressure ; - steel grades ; - mechanical properties ; - dimensions and tolerances ; - requirements for inspection and testing ; - inspection documents ; - marking ; - protection and packaging.
  • prEN 10253-4 rev

    28-01-2011
    EC110207

    Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperature or at elevated temperatures. It specifies: - the type of fittings; - type A (see 7.2) - type B (see 7.3) - the steel grades; - the mechanical properties; - the dimensions and tolerances; - the requirements for inspection and testing; - the inspection documents; - the marking; - the handling and packaging.
  • prEN 10264-2 rev

    24-02-2016
    EC106093

    Steel wire and wire products - Steel wire for ropes - Part 2: Cold drawn non alloy steel wire for ropes for general applications

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This part of this European Standard defines cold drawn non alloy steel wire used for the manufacture of: - ropes for general applications and lifts; - ropes for applications for which there is no specific EN standard. This part of this European Standard does not apply to steel wire taken from manufactured ropes. This part of this European Standard specifies the following for cold drawn non alloy steel wire for ropes for general applications: - dimensional tolerances; - mechanical characteristics; - requirements relating to the chemical composition of the steel wire; - conditions to be satisfied by any coating. In addition to the requirements of this part of this European Standard, the requirements of EN 10264-1 also apply.
  • EN ISO 10270:2008/prAC

    04-07-2008
    00262C04

    No title available

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • EN 10270-1:2011/prA1

    30-10-2013
    EC106092

    Steel wire - for mechanical springs - Part 1: Patented cold drawn unalloyed spring steel wire

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    1.1 This Eurpean Standard applies to patented cld drawn unalloyed steel wire of cicular cross-section for the manufacture of mechanical springs for static duty and dynamic duty applications – 1.2 In addition to this European Standard, the general technical delivery requirements of EN 10021 are applicable.
  • EN 10270-3:2011/prA1

    30-10-2013
    EC106091

    Steel wire for mechanical springs - Part 3: Stainless spring steel wire

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    1.1 This European Standard applies to the grades of stainless steels listed in Table 1, which are usually used in the cold drawn condition in the form of wire circular cross-section up to 10, 00 mm in diameter, for the production of springs and spring parts that are exposed to corrosive effects and sometimes to slightly increased temperatures ( see A.1). 1.2 In addition to the steels listed in Table 1 certain of the steel gardes covered by EN 10088-3 e. g. 1.4571, 1.4539, 1.4028 are also used for springs, although to much lesser extent. In these cases the mechanical properties (tensile strength, etc.) should be agreed between purchaser and supplier. Similarly, diameters between 10,00 mm and 15, 00 mm may be ordered according to this standard; in this case the parties should agree upon the required mechanical characteristics. 1.3 In addition to the European Standard the general technical delevry requirements of EN 10021 are applicable.
  • prEN 10284 rev

    17-02-2012
    EC110214

    Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard specifies the requirements for the design, performance and testing of fittings made of malleable cast iron (see also clause 5 Materials) with compression ends for polyethylene piping systems. It applies to piping systems in polyethylene (PE) materials for different application fields, such as water and gas supply, water distribution, irrigation and gaseous fuel systems. The malleable cast iron fittings specified in this standard are of compression end type for the connection of PE pipes or of transition type with combined compression ends for pipes in different materials or with combined compression and threaded ends in conformance with prEN 10226-1. Their range of sizes covers nominal outside diameters of PE pipes d n 16 to d n 125 mm and pipe thread sizes 1/2 to 4.
  • prEN 10302 rev

    10-03-2015
    EC105075

    Creep resisting steels, nickel and cobalt alloys

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    1.1 This European Standard covers the grades of wrought steels and alloys listed in Table 1 and Table 2, which are usually employed for components and equipment, for which the main requirement is their creep resistance under mechanical long-time stressing at temperatures above 500 C. NOTE – Heat resisting grades given in EN 10095 [9] may also be used for similar applications if so agreed. 1.2 This European Standard specifies the technical delivery conditions for semi-finished products, for hot or cold rolled sheet/plate and strip, hot or cold formed (cold drawn) bars, rods, wire and sections. 1.3 The general technical delivery conditions specified in EN 10021:2006 apply in addition to the specifications of this European Standard, unless otherwise specified in this European Standard. 1.4 This European Standard does not apply to components manufactured by further processing the product forms listed in 1.2 with quality characteristics altered as a result of such further processing. 1.5 This European Standard shall not be used for aerospace and pressure purposes. 1.6 For steels and alloys with similar chemical composition, but intended for different applications, see the Bibliography.
  • prEN ISO 10303-101 rev

    21-03-2008
    00310088

    Industrial automation systems and integration - Product data representation and exchange - Part 101: Integrated application resource: Draughting

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • ISO/AWI TS 10303-4000

    28-10-2019
    078709

    Industrial automation systems and integration -- Product data representation and exchange -- Part 4000: Core Model

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • EN ISO 10318-1:2015/prA1

    28-04-2015
    00189240

    Geosynthetics -- Part 1: Terms and definitions

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • EN ISO 10318-2:2015/prA1

    28-04-2015
    00189241

    Geosynthetics -- Part 2: Symbols and pictograms

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 10320 rev

    18-03-2015
    00189237

    Geotextiles and geotextile-related products - Identification on site

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 10325 rev

    27-05-2015
    00248597

    Fibre ropes - High modulus polyethylene - 8-strand braided ropes, 12-strand braided ropes and covered ropes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 10326-3

    30-09-2011
    00231103

    Mechanical vibration - Laboratory method for evaluating vehicle seat vibration - Part 3: Specification of dynamic dummies for z-axis motion

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This standard is aimed to specify physical characteristics and laboratory tests for anthropodynamic dummies based on apparent mass response and intended for use in characterising the dynamic response of a seat to vertical vibrations.