Velkommen til portalen for nye arbejdsemner

3474 Hits

ISO/TC 69/SC 4/WG 11

  • EN 10270-3:2011/prA1

    30-10-2013
    EC106091

    Steel wire for mechanical springs - Part 3: Stainless spring steel wire

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    1.1 This European Standard applies to the grades of stainless steels listed in Table 1, which are usually used in the cold drawn condition in the form of wire circular cross-section up to 10, 00 mm in diameter, for the production of springs and spring parts that are exposed to corrosive effects and sometimes to slightly increased temperatures ( see A.1). 1.2 In addition to the steels listed in Table 1 certain of the steel gardes covered by EN 10088-3 e. g. 1.4571, 1.4539, 1.4028 are also used for springs, although to much lesser extent. In these cases the mechanical properties (tensile strength, etc.) should be agreed between purchaser and supplier. Similarly, diameters between 10,00 mm and 15, 00 mm may be ordered according to this standard; in this case the parties should agree upon the required mechanical characteristics. 1.3 In addition to the European Standard the general technical delevry requirements of EN 10021 are applicable.
  • prEN 10284 rev

    17-02-2012
    EC110214

    Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard specifies the requirements for the design, performance and testing of fittings made of malleable cast iron (see also clause 5 Materials) with compression ends for polyethylene piping systems. It applies to piping systems in polyethylene (PE) materials for different application fields, such as water and gas supply, water distribution, irrigation and gaseous fuel systems. The malleable cast iron fittings specified in this standard are of compression end type for the connection of PE pipes or of transition type with combined compression ends for pipes in different materials or with combined compression and threaded ends in conformance with prEN 10226-1. Their range of sizes covers nominal outside diameters of PE pipes d n 16 to d n 125 mm and pipe thread sizes 1/2 to 4.
  • prEN 10302 rev

    10-03-2015
    EC105075

    Creep resisting steels, nickel and cobalt alloys

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    1.1 This European Standard covers the grades of wrought steels and alloys listed in Table 1 and Table 2, which are usually employed for components and equipment, for which the main requirement is their creep resistance under mechanical long-time stressing at temperatures above 500 C. NOTE – Heat resisting grades given in EN 10095 [9] may also be used for similar applications if so agreed. 1.2 This European Standard specifies the technical delivery conditions for semi-finished products, for hot or cold rolled sheet/plate and strip, hot or cold formed (cold drawn) bars, rods, wire and sections. 1.3 The general technical delivery conditions specified in EN 10021:2006 apply in addition to the specifications of this European Standard, unless otherwise specified in this European Standard. 1.4 This European Standard does not apply to components manufactured by further processing the product forms listed in 1.2 with quality characteristics altered as a result of such further processing. 1.5 This European Standard shall not be used for aerospace and pressure purposes. 1.6 For steels and alloys with similar chemical composition, but intended for different applications, see the Bibliography.
  • prEN ISO 10303-101 rev

    21-03-2008
    00310088

    Industrial automation systems and integration - Product data representation and exchange - Part 101: Integrated application resource: Draughting

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • ISO/AWI TS 10303-4000

    28-10-2019
    078709

    Industrial automation systems and integration -- Product data representation and exchange -- Part 4000: Core Model

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • EN ISO 10318-1:2015/prA1

    28-04-2015
    00189240

    Geosynthetics -- Part 1: Terms and definitions

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • EN ISO 10318-2:2015/prA1

    28-04-2015
    00189241

    Geosynthetics -- Part 2: Symbols and pictograms

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 10320 rev

    18-03-2015
    00189237

    Geotextiles and geotextile-related products - Identification on site

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 10325 rev

    27-05-2015
    00248597

    Fibre ropes - High modulus polyethylene - 8-strand braided ropes, 12-strand braided ropes and covered ropes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 10326-3

    30-09-2011
    00231103

    Mechanical vibration - Laboratory method for evaluating vehicle seat vibration - Part 3: Specification of dynamic dummies for z-axis motion

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This standard is aimed to specify physical characteristics and laboratory tests for anthropodynamic dummies based on apparent mass response and intended for use in characterising the dynamic response of a seat to vertical vibrations.
  • prEN 10328 rev

    06-11-2014
    EC101155

    Iron and steel - Determination of the conventional depth of hardening after surface heating

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This document defines the test method for the determination of the conventional depth of hardening after surface heating.
  • prEN ISO 10328 rev

    24-11-2015
    00293059

    Prosthetics - Structural testing of lower-limb prostheses - Requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 10340 rev

    21-05-2014
    EC111070

    Steel castings for structural uses

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard applies to steel castings: – for structural uses in buildings and civil engineering works. Its uses include housing and service buildings, bridges, roads, pipe network. In cases where castings are joined by welding by the founder, this European Standard applies. This European Standard does not apply in cases where castings are welded: – to wrought products (plates, tubes, forgings...); – or by non founders.
  • prEN 10340-1

    11-09-2015
    EC111071

    Steel castings for structural uses - Part 1: General

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard applies to steel castings: – for structural uses in buildings and civil engineering works. Its uses include housing and service buildings, bridges, roads, pipe network. In cases where castings are joined by welding by the founder, this European Standard applies. This European Standard does not apply in cases where castings are welded: – to wrought products (plates, tubes, forgings...); – or by non founders.
  • prEN 10340-2

    11-09-2015
    EC111072

    Steel castings for structural uses - Part 2: Technical delivery conditions

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard applies to steel castings: – for structural uses in buildings and civil engineering works. Its uses include housing and service buildings, bridges, roads, pipe network. In cases where castings are joined by welding by the founder, this European Standard applies. This European Standard does not apply in cases where castings are welded: – to wrought products (plates, tubes, forgings...); – or by non founders.
  • prEN ISO 10350-1 rev

    24-11-2015
    00249931

    Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 10350-2 rev

    24-11-2015
    00249932

    Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 10352 rev

    22-12-2015
    00249968

    Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass per unit area

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 10360-11

    07-10-2011
    00290168

    Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 11: Computed tomography

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
    Beskrivelse
    The intention is to achieve comparability with the characteristics of coordinate measuring devices with tactile and with optical sensors. The characteristics described in this part serve for the specification of coordinate measuring devices with CT sensors and for a comparison between various measurement systems.
  • prEN ISO 10360-11

    03-10-2017
    00290233

    Geometrical product specifications (GPS) – Acceptance and reverification tests for coordinate measuring machines (CMM) – Part 11: CMMs using the principle of computed tomography (CT)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
    Beskrivelse
    The purpose of this part of ISO 10360 is to define metrological characteristics and methods for testing coordinate measuring systems (CMSs) using the principle of computed tomography (CT) as a single sensor which are dedicated to dimensional measurements of technical workpieces. This excludes medical imaging, medical dimensional measurements and as well non-destructive (material) testing applications of CT (e.g. defect analyses). The intention of this part of ISO 10360 is to achieve comparability with the characteristics of coordinate measuring systems with tactile and with optical sensors. The characteristics described in this part serve both for the specification of coordinate measuring systems using the principle of computed tomography and for the comparison between various coordinate measurement systems. This standard is intentionally dedicated to the CMS using X-ray-based computed tomography where the measurements are predominantly based on the attenuation contrast visible when penetrating physical matter. This standard may also be applied to CMS using other tomographic measurement principles based on a mutual agreement. This standard covers coordinate measuring systems using sensors based on the kinematic/geometric principles of axial CT (fan and cone beam geometries) and as well helical CT as described in Annex F. This standard covers coordinate measuring systems and defines metrological characteristics and methods for testing which are intended specifically for non-gradient mono-materials which are homogeneous, i.e. cases where measurements of reference standards are performed which consist only of one (relevant) material which does not show a relevant lateral or spatial gradient in the attenuation of X-rays. This part of ISO 10360 does not define metrological characteristics and related testing methods which are dedicated to measure the influence of surface roughness on CT-based CMS measurements (cf. e.g. [XXX], [YYY] for describing the potential influence). In close reliance on ISO 10360-2 and ISO 10360-5 and as well ISO 10360-8, this standard defines the methods for acceptance testing and for the monitoring of length measurement errors and probing errors when using CT-based CMS. Therefore, this document establishes the additional aspects necessary when using CT: - Reference standards usable as alternatives to gauge blocks - Comparability of the characteristics when using alternative standards (e.g. with spherical bounding surfaces) - Comparability of the characteristics under different probing strategies (different number of points, degree of coverage of the elements to be measured) - Definition of the characteristics for various operating conditions - Notes on the treatment of affecting quantities such as environmental conditions, mathematical data filters and the nature of the measurement standard’s surface.
  • prCEN ISO/TR 10400 rev

    14-02-2018
    00012376

    Petroleum and natural gas industries – Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 10407-1

    08-06-2012
    00012092

    Petroleum and natural gas industries - Drilling and production equipment - Part 1: Recommended practice for drill stem design and operating limits

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Komite
  • prEN ISO 10438-1 rev

    20-07-2012
    00012322

    Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 10438-2 rev

    20-07-2012
    00012323

    Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2: Special-purpose oil systems

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 10438-3

    20-07-2012
    00012324

    Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite