Velkommen til portalen for nye arbejdsemner

3479 Hits

ISO/TC 69/SC 4/WG 11

  • prEN 12977-4 rev

    30-03-2015
    00312041

    Thermal solar systems and components - Custom built systems - Part 4: Performance test methods for solar combistores

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies test methods for the performance characterization of stores which are intended for use in small custom built systems as specified in EN 12977-1. Stores tested according to this document are commonly used in solar combisystems. However, the thermal performance of all other thermal stores with water as a storage medium (e.g. for heat pump systems) can be also assessed according to the test methods specified in this document. This document applies to combistores with a nominal volume up to 3 000 l and without integrated burner. NOTE – This document is extensively based on references to EN 12977-3:2012.
  • prEN 12977-5 rev

    30-03-2015
    00312042

    Thermal solar systems and components - Custom built systems - Part 5: Performance test methods for control equipment

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies performance test methods for control equipment. Furthermore, this document contains requirements on accuracy, durability and reliability of control equipment. The tests described in this document are limited to electrically activated components delivered with or for the system by the final supplier. For the purposes of this document controller and control equipment for solar heating systems and auxiliary heaters, if part of the system, are restricted to the following: a) Controllers as: 1) system clocks, timers and counters; 2) differential thermostats; 3) multi-function controllers. b) Sensors as: 1) temperature sensors; 2) irradiance sensors (for short wave radiation); 3) pressure sensors; 4) level sensors; 5) flow meters; 6) heat meters. c) Actuators as: 1) pumps; 2) solenoid and motor valves; 3) relays. d) Combinations of controllers, sensors and actuators listed above. An additional objective of the procedures described in this document is to verify control algorithms and, together with the accuracy of sensors, to determine control parameters. In addition to verifying the functioning of a controller, its equipment and actuators, the determined parameters may be used for numerical system simulations. Typically, electrical anodes are not part of the control equipment and are not controlled by the control equipment. However, because they are electrical appliances, electrical anodes are included in this document. This document is valid for control equipment of solar heating systems for the purpose of hot water preparation and/or space heating. If the solar system is connected to or part of a conventional heating system, the validity is extended to the entire system. In combination with the standards EN 12976-1, EN 12976-2 as well as EN 12977-1, EN 12977-2, EN 12977-3 and EN 12977-4, this document is valid for e) factory made solar heating systems, f) small custom built solar heating systems, g) large custo ...
  • prEN 12981 rev

    14-10-2011
    00271048

    Coating plants - Spray booths for application of organic powder coating material - Safety requirements

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    The standard is applicable to spray booths for spray application of organic coating powder.
  • prEN 12983

    01-04-2011
    00194142

    Cookware - Domestic cookware for use on top of a stove, cooker or hob

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies safety and performance requirements for items of cookware for domestic use on top of a stove, cooker or hob, on induction heating sources. It is applicable to all cookware regardless of material or method of manufacture.
  • prEN ISO 12998

    06-03-2009
    00121567

    Mechanical joining - Fatigue testing of multi-joint specimens - Specimen dimensions and test procedure (ISO/PWI 12998)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Komite
    Beskrivelse
    This International Standard specifies test specimens and procedures for performing constant load amplitude fatigue tests on multi-joined specimens.
  • prEN 13000 rev

    04-07-2017
    00147117

    Cranes - Mobile cranes

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard is applicable to the design, construction, installation of safety devices, information for use, maintenance and testing of mobile cranes as defined in ISO 4306 2. Examples of mobile crane types are given in Annex A. This European Standard does not apply to: - loader cranes (see EN 12999) - off-shore cranes (see EN 13852 1) - floating cranes (see EN 13852 2) - variable reach truck (see EN 1459) NOTE 1 – Variable Reach Trucks are commonly known as telehandlers. - mobile self-erecting tower cranes - earth-moving machinery used for object handling (see EN 474-series). This standard does not cover hazards related to the lifting of persons. NOTE 2 – The use of mobile cranes for the lifting of persons is subject to specific national regulations. Mobile cranes covered by this European Standard are designed for a limited number of stress cycles and particular properties of motions, e.g. smooth application of the driving forces and loading conditions according to ISO 4301 2:1985, group A1. For a duty cycle such as grab, magnet or similar work, additional provisions are required which are outside the scope of this European Standard. The hazards covered by this European Standard are identified by Annex C. This document is not applicable to mobile cranes which are manufactured before the date of publication of this document by CEN.
  • prEN 13001-3-4

    04-03-2015
    00147127

    Cranes - General Design - Part 3-4: Limit states and proof of competence of machinery

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard is to be used together with EN 13001-1 and EN 13001-2 and as such they specify general conditions, requirements and methods to prevent mechanical hazards of cranes by design and theoretical verification. NOTE Specific requirements for particular types of crane are given in the appropriate European Standard for the particular crane type. This European Standard covers machinery that is not dealt with by other EN 13001 standards. The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during intended use and reasonably foreseeable misuse. Clauses 4 to 7 of this standard are necessary to reduce or eliminate risks associated with the following hazards: a) exceeding the limits of strength (yield, ultimate, fatigue); b) exceeding temperature limits of material or components; c) elastic instability of the crane or its parts (buckling, bulging). This European Standard is not applicable to cranes which are manufactured before the date of its publication as EN and serves as reference base for the European Standards for particular crane types (see Annex I). NOTE prEN/ 13001-3-4 deals only with limit state method in accordance with EN 13001-1.
  • prEN 13001-3-6

    04-03-2015
    00147142

    Cranes – General design – Part 3-6: Limit states and proof of competence of machinery – Hydraulic cylinders

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    Calculation methods and limit states for theoretical verification of the mechanical strength of hydraulic cylinders used in cranes. Outline of standard The standard will have a layout that is quite similar to EN 13001-3-1. It shall specify the calculation methods and provide limit states that are necessary to reduce or eliminate risks associated with the following hazards: 1. exceeding the limits of strength (yield, ultimate, fatigue); 2. elastic instability of the crane or its parts (buckling). In particular, the following phenomena will be addressed: • Hoop stress • Shell bending stress at bottom weld • Cylinder head flange weld • Notch stress at oil connectors • Stress at cylinder head thread • Stress at piston thread • Piston weld • Locking thread • Bolted cylinder head screws • Buckling of entire cylinder • Internal buckling of rod • Compressed member with end moments or lateral displacement (2nd order theory) • Mechanical interfaces
  • prEN 13016-1 rev

    22-06-2015
    00019470

    Liquid petroleum products - Vapour pressure - Part 1: Determination of air saturated vapour pressure (ASVP) and calculated dry vapour pressure equivalent (DVPE)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies a method for the determination of the total pressure, exerted in vacuo, by volatile, low viscosity petroleum products, components, and feedstocks containing air, including oxygenated fuels up to 3,7%mass of oxygen and automotive ethanol (E85) fuel. A dry vapour pressure equivalent (DVPE) can be calculated from the air containing vapour pressure (ASVP) measurement. The conditions used in the test described in this standard are a vapour-to-liquid ratio of 4:1, a sample size of 700 ml to 800 ml, and a test temperature of 37,8 °C. This method described is suitable for testing air-saturated samples that exert an air saturated vapour pressure of between 9,0 kPa and 150,0 kPa at 37,8 °C.
  • prEN 13032-2 rev

    09-07-2015
    00169072

    Light and lighting - Measurement and presentation of photometric data of lamps and luminaires - Part 2: Presentation of data for indoor and outdoor work places

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This document specifies the required data for lamps and luminaires for the verification of conformity to the requirements of EN 12464-1 and EN 12464-2. It also specifies data that are commonly used for lighting of indoor and outdoor work places. When these data are provided, they should conform to this document.
  • prEN 13032-6

    04-09-2015
    00169073

    Road lighting – Part 6: Utilization Factors

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This part of this European Standard defines tables of the most energy efficient utilization factors and utilances for different road widths, different mounting heights, maximum luminaire spacings, different overhangs and inclinations as appropriate for given lighting classes for road lighting luminaires. Furthermore, methods for the calculation of the utilization factors and utilances together with methods for the selection of the most energy efficient utilization factors to include in tables are provided. The tables are applicable for straight sections of roads.
  • prEN 13053 rev

    19-02-2016
    00156230

    Ventilation for buildings - Air handling units - Rating and performance for units, components and sections

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies requirements and testing for ratings and performance of air handling units as a whole. It also specifies requirements, recommendations, classification, and testing of specific components and sections of air handling units. For many components and sections it refers to component standards, but it also specifies restrictions or applications of standards developed for stand alone components. This standard is applicable both to standardised designs, which may be in a range of sizes having common construction concepts, and also to custom-design units. It also applies both to air handling units, which are completely prefabricated, and to units which are built up on site. Generally the units within the scope of this standard include at least a fan, a heat exchanger and an air filter. This standard is not applicable to the following: a) air conditioning units serving a limited area in a building, such as fan coil units; b) units for residential buildings; c) units producing ventilation air mainly for a manufacturing process.
  • EN 13055:2016/prA1

    30-11-2018
    00154173

    Lightweight aggregates

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the properties of Lightweight Aggregates (LWA) and fillers derived thereof obtained by processing natural or manufactured materials and mixtures of these aggregates for concrete, mortar and grout, bituminous mixtures and surface treatments and for unbound and hydraulically bound applications in construction works. This European Standard covers LWA of mineral origin having particle densities not exceeding 2000 kg/m3 (2,000 Mg/m3) or loose bulk densities not exceeding 1200 kg/m3 (1,200 Mg/m3) including: a) natural LWA; b) LWA manufactured from natural materials; c) LWA manufactured from by-products of industrial processes or from recycled source materials; d) LWA as by-products of industrial processes. A list of source materials and specific materials, which are within the scope of this standard, is given in Annex A (normative). NOTE – Recycled aggregates from construction and demolition waste and Municipal Solid Waste Incinerator Bottom Ash (MIBA) are covered by standards EN 12620, EN 13043, EN 13139 and EN 13242. Some LWA for specific applications are covered in separate European product standards (Annex B, normative). The requirements specified in this standard may not be equally relevant to all types of LWA. For particular applications, the requirements and tolerances can be adapted for the end use.
  • prEN 13063-1 rev

    03-12-2010
    00166090

    Chimneys - System chimneys with clay/ceramic flue liners - Part 1: Requirements and test methods for sootfire resistance

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies the requirements and test methods for multiwall soot fire resistant system chimneys, working under dry conditions, with corrosion resistance 3, with negative pressure (see EN 1443) in which the products of combustion are conveyed to the atmosphere through clay/ceramic flue liners. Marking and inspection are also covered by this standard. This standard does not apply to structurally independent (free standing or self supporting) system chimneys. A soot fire resistant system chimney has the following items where appropriate: - clay/ceramic flue liners; - Insulation layer; - outer walls; - mortar for jointing flue liners; - mortar for jointing outer walls; - terminal; - chimney base; - cladding; - opening section; - cleaning and inspection door; - distance piece; - reinforcement. The soot fire resistant chimney covers a combination of compatible chimney components, obtained or specified from one manufacturing source with product responsibility for the whole chimney.
  • prEN 13063-2 rev

    03-12-2010
    00166091

    Chimneys - System chimneys with clay/ceramic flue liners - Part 2: Requirements and test methods under wet conditions

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies the requirements and test methods for multiwall system chimneys working under wet conditions (in the following expressed as ""wet chimney"") with pressure type N1, N2 or P1 according to EN 1443 and a working temperature below or equal T600 according to prEN 13063-1, in which the products of combustion are conveyed to the atmosphere through clay/ceramic flue liners. Marking and inspection are also covered by this document. This European Standard does not apply to structurally independent (free standing or self supporting) system chimneys. The wet chimney may comprise the following appropriate components: - clay/ceramic flue liners; - insulation layer; - outer walls; - acid resistant mortar for jointing flue liners or elastomeric sealant; - mortar for jointing outer walls; - terminal; - chimney base; - condensate collector; - condensate outlet; - cladding; - opening section; - cleaning and inspection door; - distance piece; - reinforcement. The wet system chimney covers a combination of compatible chimney components, obtained or specified from one manufacturing source with product responsibility for the whole system chimney. NOTE – This document does not cover soot fire resistance chimneys.
  • prEN 13071-1 rev

    17-02-2016
    00183092

    Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 1: General requirements

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    The standard specifies requirements for stationary waste containers up to 5 000 l, top lifted bottom emptied for collection of solid non hazardous waste.
  • prEN 13071-2 rev

    17-02-2016
    00183093

    Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    The standard specifies additional requirements for underground or partly underground systems, top lifted bottom emptied for collection of solid non hazardous waste in stationary waste containers up to 5 000 l.
  • prEN 13087-11

    14-07-2006
    00158064

    Protective helmets - Test methods - Part 11: Rotational effects of impacts

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
  • prEN 13088 rev

    01-01-2016
    00443005

    Manufactured articles filled with feather and down - Method for the determination of a filled product's total mass and for the determination of the mass of the filling

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN 13101 rev

    30-11-2012
    00165260

    Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This standard specifies general requirements and testing methods for steps manufactured from cast iron, steel or aluminium, for use in manholes and other underground man entry chambers as a means of access. This standard specifies performance criteria for mechanical stability and resistance providing protection against falling. Corresponding test methods and evaluation of conformity are included. The steps specified in this European Standard are suitable for use in sewage, surface water and, subject to the requirements of national regulations, potable water environments. Where steps are to be used in particular corrosive environments, e.g. industrial effluents, additional protection may be required. This standard does not apply for steps moulded in prefabricated manholes of the same material.
  • prEN ISO 13120 rev

    16-09-2015
    00251321

    Health informatics -- Syntax to represent the content of healthcare classification systems -- Classification Markup Language (ClaML)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN 13126-18

    22-04-2011
    00033443

    Building hardware - Specifications for the fittings for the operation of windows and door height windows - Part 18: Requirements and test procedures for durability, strength, security and functionality of Fan light openers for windows and door height windows

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This part of EN 13126 specifies requirements and test procedures for durability, strength, security and functionality of Fan light openers for windows and door height windows.
  • prEN 13126-6 rev

    24-11-2015
    00033516

    Building hardware - Requirements and test methods for windows and doors height windows - Part 6: Variable geometry stay hinges (with or without a friction stay)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This part of EN 13126 specifies requirements and test methods for durability, strength, security and function of mechanically operated variable geometry stay hinges (with or without a friction system). By means of this standard, the user of recognized tested hardware can assume that with correct usage, the variable geometry stay hinges (with or without a friction system) for windows conform to prescribed requirements.
  • prEN 13126-8 rev

    24-11-2015
    00033515

    Building hardware - requirements and test methods for windows and doors height windows - Part 8: Tilt and turn, tilt- first and turn-only hardware

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the requirements and test procedures for durability, strength, security and function of tilt and turn, tilt-first and turn-only hardware components or sets for windows and door height windows in accordance with common application as shown in informative Annex C.
  • prEN 13134 rev

    15-05-2009
    00121577

    Brazing - Procedure approval

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    The document defines general rules (test procedures, test pieces) for the specification and approval of brazing procedures for all materials, metallic and non-metallic.