Velkommen til portalen for nye arbejdsemner

3469 Hits

CEN/TC 292

  • EN 13160-5:2016/prA1

    11-10-2017
    00393056

    Leak detection systems – Part 5: Requirements and test/assessment methods for in-tank gauge systems and pressurised pipework systems

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard gives requirements and corresponding test\assessment methods applicable to leak detection kits, based upon volumetric loss from within the tank and/or pipework system. The kits usually comprise: - Measuring Device - Evaluation Device - Alarm Device Intended use: Leak Detection kits are intended to be used in\with single or double skin underground tanks or single or double skin underground and/or aboveground, pipework designed for flammable liquids having a flash point not exceeding 100 °C.
  • EN 13160-7:2016/prA1

    11-10-2017
    00393057

    Leak detection systems – Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard gives requirements and the corresponding test/assessment methods applicable to leak detection lining kits and leak detection jacket kits. Leak detection lining kits and leak detection jackets kits intended to be used as post-installed to create an interstitial space or leakage containment in single skin underground or above ground, non-pressurized, tanks designed for water polluting liquids. The kit has to be used only in conjunction with leak detection kits covered by prEN 13160-2 to prEN 13160-4.
  • EN 13163:2012+A1:2015/prA2

    09-06-2015
    00088399

    Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the requirements for factory made products of expanded polystyrene, with or without facings or coatings, which are used for the thermal insulation of buildings. The products are manufactured in the form of boards or rolls or other preformed ware. This European Standard specifies product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this European Standard are also used for sound insulation and in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required class or level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The classes and levels required for a given application are to be found in regulations or non conflicting standards. Products with a declared thermal resistance lower than 0,25 m2?K/W or a declared thermal conductivity at 10 °C greater than 0,060 W/(m•K) are not covered by this European Standard.
  • prEN ISO 13173

    30-01-2009
    00219049

    Cathodic protection for steel offshore floating structures

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 13174

    30-01-2009
    00219050

    Cathodic protection for harbour installations

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • EN 13175:2014/prA1

    12-03-2015
    00286170

    LPG Equipment and accessories - Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies minimum requirements for the design, testing and production testing of valves, including appropriate fittings, which are connected to mobile or static LPG pressure vessels above 150 l water capacity. Pressure relief valves and their ancillary equipment, contents gauges and automotive LPG components are outside the scope of this European Standard. This European Standard does not apply to refineries or other process plants.
  • prEN 13176 rev

    19-11-2014
    00164588

    Flexible hose assemblies in drinking water installations - Functional requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the requirements and test methods for materials, dimensions and function for flexible hose assemblies for drinking water installations, braided or not, designed for use with drinking water with an allowable maximum operating pressure (PMA) of 1 MPa and maximum operating temperature 70 °C to connect sanitary tap ware, heaters and similar appliances.
  • prEN 13185 rev

    25-09-2014
    00138216

    Non-destructive testing - Leak testing - Tracer gas method

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard describes the techniques to be applied for the detection of a leak, using a tracer gas and a tracer gas specific leak detector
  • prEN 13192 rev

    25-09-2014
    00138217

    Non-destructive testing - Leak testing - Calibration of reference leaks for gases

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This draft European Standard specifies the calibration of those leaks that are used for the adjustment of leak detectors for the determination of leakage rate in everyday use. The preferred calibration method in this case is a comparison with a standard leak. In this way the leaks used for routine use become traceable to a primary standard as the ISO 9000 series of standards require. The comparison procedures are preferably applicable to helium leaks, because this test gas can be selectively measured by a mass spectrometer leak detector (MSLD) (the definition of MLSD is given in EN 1330-8). Calibration by comparison (see methods A and B below) with known standard leaks is easily possible for leaks with reservoir and leakage rates below 10-7Pa.m3/s. From 10-7 Pa.m3/s to 10-4 Pa.m3/s no leaks reliable enough to be used as transfer standard exist. Leaks in this range can only be calibrated by measurement of flow in a calibrated capillary tube (see method C below). Leakage rates greater than 10-4 Pa.m3/s can be measured by flow meters calibrated against primary national standards.
  • prEN 13200-6 rev

    28-08-2015
    00315020

    Spectator facilities - Part 6 : Demountable stands

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies product characteristics for demountable stands at permanent or temporary entertainment venues including sports stadium, sport halls and indoor and outdoor facilities. Stands in fairgrounds and amusement parks are excluded from this standard. This Standard is not applicable to stands of moveable type which last row of places for spectators is under 1 m height from the ground. Note: Amusement parks are covered by EN 13814 Fairground and amusement park machinery and structures – safety.
  • prEN 13200-9

    20-11-2009
    00315013

    Communication systems in spectator facilities

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European standard specifies general characteristics of Communication Systems used in Spectator Facilities
  • prEN 13207 rev

    10-11-2015
    00249832

    Plastics - Thermoplastic silage films - Specifications and methods of test

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    See title
  • prEN 13209-1 rev

    05-04-2016
    00252071

    Child use and care articles - Baby carriers - Safety requirements and test methods - Part 1: Framed back carriers

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the safety requirements and test methods for child back carriers with framed support to carry the child in an essentially seated position. Framed back carriers are intended for children from 6 months of age up to a maximum weight of 22kg and are designed to be attached to a carer’s torso allowing a hands-free operation e.g.: standing, walking. If the framed back carrier has other functions not covered in this European Standard, reference should be made to the relevant European Standard.
  • EN 13241-1:2003+A1:2011/prA2

    06-10-2015
    00033509

    Industrial, commercial and garage doors and gates - Product standard - Part 1: Products without fire resistance or smoke control characteristics

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    1.1 General This European Standard specifies the safety and performance requirements for doors, gates and barriers, intended for installation in areas in the reach of persons, and for which the main intended uses are giving safe access for goods and vehicles accompanied or driven by persons in industrial, commercial or residential premises. This European Standard also covers commercial doors such as rolling shutters and rolling grilles used in retail premises which are mainly provided for the access of persons rather than vehicles or goods. These doors can include pass doors incorporated in the door leaf which are also covered by this European Standard. These devices can be manually or power operated. This European Standard does not cover operation in environments where the electromagnetic disturbances are outside the range of those specified in EN 61000-6-3. 1.2 Exclusions This European Standard does not apply to the following which are intended for a different use: - lock gates and dock gates; - doors on lifts; - doors on vehicles; - armoured doors; - doors mainly for the retention of animals; - theatre textile curtains; - horizontally moving manually operated pedestrian doors with a leaf size less than 6,25 m²; - horizontally moving power operated doors less than 2,5 m wide and 6,25 m² area, designed principally for pedestrian use in accordance with prEN 12650-1; - revolving doors of any size; - railway barriers; - barriers used solely for vehicles. This European Standard does not cover the radio part of doors. If a radio operating device is used, the relevant ETSI standards should be applied in addition. This European Standard does not contain any specific requirements for fire resistance or smoke control characteristics which are covered in prEN 13241-2. !deleted text" (....)
  • prEN 13261 rev

    22-11-2013
    00256666

    Railway applications - Wheelsets and bogies - Axles - Product requirements

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    The same as for EN 13261.
  • prEN 13261 rev

    11-11-2015
    00256810

    Railway applications - Wheelsets and bogies - Axles - Product requirements

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the characteristics of axles for use on European networks. It defines characteristics of forged or rolled solid and hollow axles, made from vacuum-degassed steel grade EA1N1 that is the most commonly used grade on European networks. For hollow axles, this standard applies only to those that are manufactured by machining of a hole in a forged or rolled solid axle In addition, the particular characteristics for axles in grade EA1T1 and EA4T1 are given in Annex A. Two categories of axle are defined, category 1 and category 2. Generally, category 1 is chosen when the operational speed is higher than 200 km/h. This standard is applicable to axles that are designed in accordance with the requirements of EN 13103 and EN 13104. NOTE – Different values for some characteristics may be agreed if a particular process of fabrication (e.g. cold rolling, shot peening, shot peening, steel cleanliness, reduction ratio, improved material properties from melting and heat treatment processes, etc.) has an influence on them.
  • prEN 13262 rev

    25-05-2015
    00256776

    Railway applications - Wheelsets and bogies - Wheels - Product requirements

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the characteristics of railway wheels for use on European networks. !Four steel grades, ER6, ER7, ER8 and ER9 are defined in this standard; for European freight wagon interoperability purposes only grades ER6, ER7 and ER8 are applicable. NOTE 1 Grade ER6 is not normally fit for the duty of application to freight wagons; it is normally applied in low axleload situations." !Certain characteristics are defined according to a category 1 or a category 2. Category 1 is generally chosen when the train speed is higher than 200 km/h. Freight vehicles running at speeds lower than 200 km/h generally use wheels of Category 2." These categories can sometimes be subdivided, depending upon the characteristics. This standard is applicable to solid forged and rolled wheels which are made from vacuum degassed steel and have a chilled rim. They are to have already been used in commercial conditions on a European network in a significant quantity, or to have satisfied a technical approval procedure according to EN 13979-1 for their design. !NOTE 2" The definition of other wheels may be found in other documents, such as UIC leaflets or ISO standards. !NOTE 3" The technical approval procedure is not within the scope of this standard. !NOTE 4" Rim-chilled" describes heat treatment of the rim, the aim of which is to harden the rim and to create compressive residual stresses in the rim.
  • prEN 13268

    08-12-2006
    00276061

    Suface active agents - Determination of ethylene oxide and propylene oxide groups in ethylene oxide and propylene oxide adducts

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies a method for the qualitative and quantitative determination of ethylene oxide and propylene oxide groups in ethylene oxide (EO) and propylene oxide (PO) adducts, polyethers and polyglycol esters. NOTE – If a suitable calibration is performed, methoxy groups can also be determined.
  • prEN 13277-8

    05-10-2012
    00162352

    Protective equipment for martial arts - Part 8: Karate face protectors

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies additional requirements and test methods for facial protectors for the practice of karate.
  • EN 13285:2010/prA1

    13-07-2012
    00227361

    Unbound mixtures - Specifications - Amendment on Factory Production Control and Annex ZA

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies requirements for unbound mixtures used for construction and maintenance of roads, airfields and other trafficked areas. The requirements are defined with appropriate cross-reference to EN 13242. This European Standard applies to unbound mixtures of natural, artificial and recycled aggregates with a upper sieve size (D) from 8 mm to 90 mm and lower sieve size (d) = 0 at the point of delivery. NOTE 1 Mixtures with an upper sieve size (D) greater than 90 mm are not covered by this European Standard but may be specified in the place of use. NOTE 2 Water content of the mixture and the density of the installed layer are not specified mixture requirements. Both parameters are related to the control of the construction of the layer and are outside the scope of this European Standard.
  • prEN ISO 13297 rev

    28-07-2015
    CST01142

    Small craft -- Electrical systems -- Alternating current installations

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN 13302 rev

    02-06-2015
    00336187

    Bitumen and bituminous binders - Determination of dynamic viscosity of bituminous binder using a rotating spindle apparatus

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies a method for the determination of the dynamic viscosity of a variety of bituminous binders: modified and unmodified bituminous binders, bituminous emulsions, cut-back and fluxed bituminous binders, by means of a coaxial viscometer. Standard application temperatures are quoted, although the dynamic viscosity can be measured at other temperatures if required. Similarly, viscosity is quoted at standard rates of shear, although additional measures can be taken at varying shear rates if required. WARNING The use of this standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
  • prEN 13313 rev

    11-02-2016
    00182075

    Refrigerating systems and heat pumps - Competence of personnel

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard defines the activities related to refrigerating circuits and the associated competence profiles and establishes procedures for assessing the competence of persons who carry out these activities. NOTE – As a refrigerating circuit is considered not to incorporate electrical and electronic systems, activities in this area are not part of this standard. For competences on electrical and electronic systems, it is recommended to refer to national regulations or appropriate European or national standards. This European Standard does not apply to persons carrying out work on self contained refrigerating systems as defined in EN 378-1 from the initial design of the product to the complete manufacture of the product, provided the process is controlled and the methods used are checked by an organisation or individual, responsible for the compliance with statutory requirements on health, safety and environment.
  • prEN 13319 rev

    21-05-2015
    00136380

    Diving accessories - Depth gauges and combined depth and time measuring devices - Functional and safety requirements, test methods

    Oprindelse:
    CEN
    Emner
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This standard specifies functional and safety requirements for depth gauges, depth gauge features of other instruments, and both depth and time measurement features of other instruments. This standard is not applicable to any information displayed to the user besides depth and time. Any information on decompression obligations displayed by equipment covered by this standard is explicitly excluded from its scope. This standard is applicable to instruments measuring water depthby the environmental pressure as used by divers. Requirements for time measurement are only applicable if intruments are automatically counting the dive time.
  • prEN 13341 rev

    03-07-2015
    00266020

    Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This document specifies requirements for materials, physical properties and performance of single blow moulded and rotationally moulded polyethylene tanks and of rotationally moulded tanks made of anionically polymerized polyamide 6, with or without reinforcements, for above ground storage of domestic heating oil, kerosene and diesel fuels for the supply of building heating/cooling systems. It is only applicable to static blow moulded and rotationally moulded polyethylene tanks and to rotationally moulded tanks made of anionically polymerized polyamide 6 that are subject to atmospheric pressure, but not subject to any external loading and have a capacity from 400 l up to 10 000 l.