Velkommen til portalen for nye arbejdsemner

39 Hits

DS/S-103-Plastrørsystemer


Næste >
  • ISO/NP 4065

    18-10-2013
    065254

    Thermoplastics pipes -- Universal wall thickness table

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • ISO/NP 6964

    31-01-2014
    063054

    Polyolefin pipes and fittings -- Determination of carbon black content by calcination and pyrolysis -- Test method and basic specification

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • ISO/NP 8521

    17-02-2015
    068569

    Plastics piping systems -- Glass-reinforced thermosetting plastics (GRP) pipes -- Test methods for the determination of the apparent initial circumferential tensile strength

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • ISO/NP 11922-1

    18-10-2013
    065255

    Thermoplastics pipes for the conveyance of fluids -- Dimensions and tolerances - Metric series

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • ISO/NP 21138-2

    13-10-2015
    069997

    Plastics piping systems for non-pressure underground drainage and sewerage -- Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)-- Part 2: Pipes and fittings with smooth external surface, Type A

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • ISO/NP 21138-3

    13-10-2015
    069998

    Plastics piping systems for non-pressure underground drainage and sewerage -- Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)-- Part 3: Pipes and fittings with non-smooth external surface, Type B

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • ISO/NP 21138-4

    09-10-2014
    066988

    Plastics piping systems for non-pressure underground drainage and sewerage -- Structured-wall piping systems of unplasticized poly(vinyl choride) (PVC-U), polypropylene (PP) and polyethylene (PE)-- Part 4: Dual and triple wall corrugated pipes and fittings, Type C

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • ISO/NP 21225-1

    22-02-2016
    070113

    Plastics piping systems for the trenchless replacement of underground pipeline networks-- Part 1: Replacement on the line by pipe bursting and pipe removal

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • ISO/NP 21225-2

    22-02-2016
    070114

    Plastics piping systems for the trenchless replacement of underground pipeline networks-- Part 2: Replacement off the line by horizontal directional drilling and impact moling

    Oprindelse:
    ISO
    Status
    Forslag om nyt arbejdsemne vedtaget
  • No reference

    11-11-2014
    00155824

    Plastics piping systems - Components for storm water handling - Specifications for storm water boxes made of PP and PVC

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This Part of EN XXXX gives the definitions and specifies the requirements for injection moulded and extruded thermoplastics boxes, including integral components, used in underground systems for infiltration, attenuation and storage of non-potable water [e.g. storm water] and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) or polypropylene with mineral modifier (PP-MD). These products are intended for underground use in landscape, pedestrian or vehicular traffic areas and are used outside the building structure (application area code “U”). These boxes are intended to be used as elements in a modular system. This European Standard is only applicable to boxes where the manufacturer has clearly stated in the documentation how the components shall be assembled to create a complete infiltration, attenuation or storage construction. Sub component(s) can be manufactured by various methods e.g. extrusion, injection moulding, rotational moulding, thermoforming and low-pressure injection moulding. A box can either be factory assembled or site assembled from different components.
  • EN 1329-1:2014/prA1

    18-11-2015
    00155859

    Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This part of EN 1329 specifies the requirements for solid wall unplasticised poly(vinyl chloride) (PVC-U) pipes, fittings and the system intended for: - soil and waste discharge applications (low and high temperature) inside buildings (application area code "B"); - soil and waste discharge applications (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD"). NOTE 1 – The intended use is reflected in the marking of products by "B" or "BD". NOTE 2 – For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm. This part of EN 1329 is also applicable to PVC-U pipes, fittings and the system intended for the following purposes: - ventilating part of the pipework in association with discharge applications; - rainwater pipework within the building structure. It also specifies the test parameters for the test method referred to in this standard. This standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours. NOTE 3 – It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. For external above ground application additional requirements depending on the climate should be agreed between the manufacturer and the user. NOTE 4 – Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 15. NOTE 5 – Joints and adhesives are considered to be part of the system as covered in the scope.
  • EN 1796:2013/prA1

    11-07-2014
    00155822

    Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for water supply (drinking or raw) with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together. It is the responsibility of the purchaser or specifier to make the appropriate selections taking into account their particular requirements and any relevant national regulations and installation practices or codes. This European Standard is applicable to GRP-UP, with flexible or rigid joints (see 3.33 and 3.34), primarily intended for use in buried installations. It is applicable to pipes, fittings and their joints of nominal sizes from DN 100 to DN 4000, which are intended to be used for the conveyance of water at temperatures up to 50 °C, with or without pressure. This European Standard covers a range of nominal sizes, nominal stiffnesses and nominal pressures. This European Standard is applicable to fittings made using any of the following techniques: a) fabricated from straight pipe; b) moulded by: 1) filament winding; 2) tape winding; 3) contact moulding; 4) hot or cold press moulding. This European Standard is applicable to the joints to be used in GRP-UP piping systems to be used for the conveyance of water, both buried and non-buried. It is applicable to joints, which are or are not intended to be resistant to axial loading. It covers requirements to prove the design of the joint. It specifies type test performance requirements for the following joints as a function of the declared nominal pressure rating of the pipeline or system: c) socket-and-spigot (either integral with pipe or sleeve coupling) or mechanical joint; d) locked socket-and-spigot joint; e) cemented or wrapped joint; f) bolted flange joint. Recommended practices for the installation of buried pipes made i ...
  • prEN ISO 11295

    16-10-2015
    00155847

    Classification and information on design and applications of plastics piping systems used for renovation and replacement

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 11296-1 rev

    04-11-2015
    00155849

    Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 11296-2

    21-06-2015
    00155841

    Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This Part 2 of EN 13566, read in conjunction with Part 1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of non-pressure drainage and sewerage networks. It covers; - homogeneous-wall (HW) pipes made of polyethylene (PE) or polypropylene (PP), - structured-wall (SW) pipes of the corrugated double-wall type of construction as defined in Annex B, whose structural layer(s) is (are) made of PE or PP, - jointing of pipe lengths by means of butt fusion (HW) ) or electrofusion (SW), - fabricated and injection-moulded fittings made of PE, PP and poly(vinyl chloride) (PVC-U). NOTE – The grouting procedure is outside the scope of this standard.
  • EN ISO 11296-3:2011/prAC

    15-04-2011
    00155C08

    Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2009)

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 11296-3

    04-11-2015
    00155850

    Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 11296-4 rev

    04-11-2015
    00155851

    Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 11296-7 rev

    04-11-2015
    00155852

    Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 11297-1 rev

    04-11-2015
    00155853

    Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 1: General

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 11297-2

    21-06-2015
    00155842

    Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 2: Lining with continuous pipes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This International Standard, read in conjunction with Part 1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground drainage and sewerage networks under pressure. It is applicable to PE pipes of three different types: - PE solid wall single layered pipes (nominal outside diameter, dn ), including any identification stripes; - PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating; - PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe (“coated pipe”), see Annex A. In addition it covers: - jointing of pipe lengths by means of butt fusion; - fabricated and injection-moulded fittings made of PE;
  • prEN ISO 11297-3 rev

    04-11-2015
    00155854

    Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3: Lining with close-fit pipes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 11297-4

    21-06-2015
    00155843

    Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 4: Lining with cured-in-place pipes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This International Standard, in conjunction with ISO 11297-1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground drainage and sewerage networks under pressure. It applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials and other process-related plastics components.
  • prEN ISO 11298-1

    04-11-2015
    00155855

    Plastics piping systems for renovation of underground water supply networks - Part 1: General

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
  • prEN ISO 11298-2

    21-06-2015
    00155844

    Plastics piping systems for renovation of underground water supply networks — Part 2: Lining with continuous pipes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This International Standard, read in conjunction with Part 1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground water supply networks. It is applicable to PE pipes of three different types: - PE solid wall single layered pipes (nominal outside diameter, dn ), including any identification stripes; - PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating; - PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe (“coated pipe”), see Annex A. In addition it covers: - jointing of pipe lengths by means of butt fusion; - fabricated and injection-moulded fittings made of PE;

Næste >