Velkommen til portalen for nye arbejdsemner

7 Hits

DS/S-250-Maskinsikkerhed


  • prEN ISO 13849-1

    25-04-2017
    00114177

    Safety of machinery – Safety-related parts of control systems – Part 1: General principles for design

    Oprindelse:
    CEN
    International kategori
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 13851

    03-03-2016
    00114174

    Safety of machinery - Two-hand control devices - Functional aspects and design principles

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
    Beskrivelse
    This European Standard specifies the safety requirements of a two-hand control device and the dependency of the output signal from the input signals and describes the main characteristics of two-hand control devices for the achievement of safety and sets out combinations of functional characteristics for three types. It does not apply to devices intended to be used as enabling devices, as hold-to-run devices or as special control devices. This European Standard provides requirements and guidance on the design and selection (based on a risk assessment) of two-hand control devices including their assessment, the prevention of defeat and the avoidance of faults. It also provides requirements and guidance for two-hand control devices containing a programmable electronic system. It applies to all two-hand control devices, independent of the energy used, including two-hand control devices which are or are not integral parts of a machine and two-hand control devices which consist of one or more than one separate element.
  • prEN ISO 13854

    01-09-2014
    00114168

    Safety of machinery - Minimum gaps to avoid crushing of parts of the human body

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
    Beskrivelse
    This European Standard specifies minimum gaps relative to parts of the human body and is applicable when adequate safety can be achieved by this method. Its object is to enable the user (e.g. standard makers, designers of machinery) to avoid hazards from crushing zones. This European Standard is applicable to risks from crushing hazards only and is not applicable to other possible hazards, e.g. impact, shearing, drawing-in.
  • prEN ISO 13857 rev

    29-07-2015
    00114172

    Safety of machinery -- Safety distances to prevent hazard zones being reached by upper and lower limbs

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
  • prEN ISO 14118

    01-09-2014
    00114169

    Safety of machinery - Prevention of unexpected start-up

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite
    Beskrivelse
    This European Standard specifies designed-in means aimed at preventing unexpected machine start-up to allow safe human interventions in hazard zones. It applies to unexpected start-up from all types of energy source, i.e. power supply, e.g. electrical, hydraulic, pneumatic, stored energy due to, e.g., gravity, compressed springs and external influences, e.g. from wind.
  • EN 15895:2011/prA1

    28-04-2015
    00213004

    Cartridge operated hand-held tools - Safety requirements - Fixing and hard marking tools

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European standard covers safety requirements for cartridge operated fixing and hard marking tools which operate with an intermediate member (piston). This European standard deals with all significant hazards, hazardous situations and events relevant to cartridge operated fixing and hard marking tools, when they are used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4). It deals with the significant hazards in the different operating modes and intervention procedures as referred to in EN ISO 12100-1:2003, 5.3. Although the safe use of cartridge operated tools depends to an important extent on the use of appropriate cartridges and fasteners, this standard is not formulating requirements for the cartridges and fasteners to be used with the tools (see Clause 7). This European Standard applies to tools designed for use with cartridges with casings made of metal or plastic and with solid propellant and containing a minor quantity of primer with a composition different from that of the main propellant. The fixing tools in the scope are those intended for use with fasteners made from metal. NOTE Information about cartridges can be found in the publication of the Permanent International Commission for the Proof of Small Arms (C.I.P.). This European standard is not applicable to cartridge operated fixing and hard marking tools which are manufactured before the date of its publication as EN.
  • prCEN ISO/TR 22100-1

    23-02-2016
    00114173

    Safety of machinery - Relationship with ISO 12100 - Part 1: How ISO 12100 relates to type-B and type-C standards

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Komite