Velkommen til portalen for nye arbejdsemner

11 Hits

DS/S-401-Skorstensforum


  • No reference

    04-12-2009
    00166079

    Chimneys - Accessories - Part 4: Flue dampers - Requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European standard specifies the requirements and test methods for flue dampers that are used as components, carrying flue gases, in order to limit the flow in a chimney. Flue dampers may be manually adjusted, sited in connecting flue pipes or chimneys, in order to reduce the burning rate (stoves/fireplaces), or mechanically or thermally driven for reducing/closing the flue, in order to reduce the stand-by losses (gas appliances type B). Components tested together with the liner or system chimney are not covered by this standard.
  • No reference

    04-12-2009
    00166080

    Chimneys - Accessories - Part 5: Explosion/implosion relief devices - Requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European standard specifies the requirements and test methods for explosion/ implosion relief devices that are used as components, carrying flue gases, in order to prevent damage in the heating appliance and chimney. Components tested together with the liner or system chimney are not covered by this standard.
  • No reference

    11-11-2011
    00166095

    Chimneys - Fire resistance tests for service installations

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This standard specifies a procedure to determine the resistance time for chimneys under standardized fire conditions. The test examines the behaviour of chimneys products exposed to fire from the outside (chimney A) and fire inside (chimney B) the chimney product (both considered as external to external, according to EN 1443). This European Standard is not applicable to: – sootfire resistance condition – doors of inspection openings unless to included in the chimney to be tested; – two or three sided shafts; The standard also applies to the testing of combined natural draught shafts used for ventilation and to supply combustion air to the appliance.
  • No reference

    01-06-2012
    00166101

    Chimneys - System chimneys with clay/ceramic flue liners - Part 3: Requirements and test methods for air flue system chimneys

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This product standard specifies the requirements and test methods for dry (designated D) and/or wet (designated W) air flue system chimneys, including terminals in which the products of combustion are conveyed to the atmosphere through clay/ceramic flue liners and combustion air is conveyed to suitable room-sealed appliances through an air duct or an air gap. It also specifies the requirements for marking, manufacturer's instructions, product information and evaluation of conformity. This standard does not apply to structurally independent (free standing or self supporting) system chimneys. The air flue system chimney covers a combination of compatible chimney components obtained or specified from one manufacturing source, with product responsibility for the whole chimney.
  • No reference

    23-05-2016
    00166076

    Chimneys - Accessories - Part 1: Silencers - Requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European standard specifies the requirements and test methods for silencers that are used as components, carrying flue gases, in order to reduce the noise which comes from combustion appliances (e. g. heating appliances, generators, CHP-units). Components tested together with the liner or system chimney are not covered by this standard.
  • prEN 1457 rev

    30-03-2007
    00166061

    Chimneys - Clay/Ceramic Flue Liners - Requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European standard is a product standard for clay/ceramic flue liners with solid walls or walls with vertical perforations for use in the construction of chimneys and flue pipes which serve to convey products of combustion from fireplaces or heating appliances to the atmosphere by negative or positive pressure. It includes the flue liners used for domestic and industrial chimneys which are not structurally independent (free-standing). This standard specifies the performance requirements for factory made flue liners and chimney fittings. Testing, marking and inspection are covered by this standard.
  • prEN 1457-1 rev

    02-06-2015
    00166109

    Chimney - Clay/ceramic flue liners - Part 1: Flue liners operating under dry conditions - Requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard is a product standard for clay/ceramic flue liners operating under dry conditions with solid walls or walls with vertical perforations for use in the construction of multiwall chimneys and flue pipes which serve to convey products of combustion from fireplaces or heating appliances to the outside atmosphere by negative or positive pressure. It includes the flue liners used for domestic and industrial chimneys which are not structurally independent (free-standing). This European Standard specifies the performance requirements for factory made flue liners and chimney fittings. Testing including thermal testing with or without insulation, marking and inspection are covered by this standard. This part does not cover flue liners operating under wet conditions.
  • prEN 1457-2 rev

    02-06-2015
    00166110

    Chimneys - Clay/ceramic flue liners - Part 2: Flue liners operating under wet conditions - Requirements and test methods

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This European Standard is a product standard for clay/ceramic flue liners operating under wet conditions with solid walls or walls with vertical perforations for use in the construction of multiwall chimneys and flue pipes which serve to convey products of combustion from fireplaces or heating appliances to the outside atmosphere by negative or positive pressure. It includes the flue liners used for domestic and industrial chimneys which are not structurally independent (free-standing). This European Standard specifies the performance requirements for factory made flue liners and chimney fittings. Testing including thermal testing with or without insulation, marking and inspection are covered by this standard. Flue liners that are specified to this standard will meet the requirements of EN 1457-1 with the same working temperature, pressure, designation and soot fire resistance.
  • prEN 1856-2 rev

    01-12-2014
    00166106

    Chimneys - Requirements for metal chimneys - Part 2: Metal flue liners and connecting flue pipes

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne vedtaget
    Beskrivelse
    This document specifies the performance requirements for rigid or flexible metal flue liners, rigid metal connecting flue pipes and their fittings used to convey the products of combustion from appliances to the outside atmosphere (including their supports). Vitreous enamelled connecting flue pipes are also covered by this document. Rigid flue liners can be used as flue liners for renovation or adaptation of existing chimneys and as flue liners of custom built chimneys. Flexible metal flue liners described in this document are exclusively for renovation or adaptation of existing chimneys. Flexible connecting flue pipes and extensible flexible products designed to be compressed or extended along their length are excluded from the scope of this document. This document also specifies the requirements for marking, manufacturer's instructions, product information and evaluation of conformity. Single wall and multi-wall system chimney products are covered by EN 1856-1.
  • prEN 13063-1 rev

    03-12-2010
    00166090

    Chimneys - System chimneys with clay/ceramic flue liners - Part 1: Requirements and test methods for sootfire resistance

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies the requirements and test methods for multiwall soot fire resistant system chimneys, working under dry conditions, with corrosion resistance 3, with negative pressure (see EN 1443) in which the products of combustion are conveyed to the atmosphere through clay/ceramic flue liners. Marking and inspection are also covered by this standard. This standard does not apply to structurally independent (free standing or self supporting) system chimneys. A soot fire resistant system chimney has the following items where appropriate: - clay/ceramic flue liners; - Insulation layer; - outer walls; - mortar for jointing flue liners; - mortar for jointing outer walls; - terminal; - chimney base; - cladding; - opening section; - cleaning and inspection door; - distance piece; - reinforcement. The soot fire resistant chimney covers a combination of compatible chimney components, obtained or specified from one manufacturing source with product responsibility for the whole chimney.
  • prEN 13063-2 rev

    03-12-2010
    00166091

    Chimneys - System chimneys with clay/ceramic flue liners - Part 2: Requirements and test methods under wet conditions

    Oprindelse:
    CEN
    Status
    Forslag om nyt arbejdsemne under udarbejdelse
    Beskrivelse
    This European Standard specifies the requirements and test methods for multiwall system chimneys working under wet conditions (in the following expressed as ""wet chimney"") with pressure type N1, N2 or P1 according to EN 1443 and a working temperature below or equal T600 according to prEN 13063-1, in which the products of combustion are conveyed to the atmosphere through clay/ceramic flue liners. Marking and inspection are also covered by this document. This European Standard does not apply to structurally independent (free standing or self supporting) system chimneys. The wet chimney may comprise the following appropriate components: - clay/ceramic flue liners; - insulation layer; - outer walls; - acid resistant mortar for jointing flue liners or elastomeric sealant; - mortar for jointing outer walls; - terminal; - chimney base; - condensate collector; - condensate outlet; - cladding; - opening section; - cleaning and inspection door; - distance piece; - reinforcement. The wet system chimney covers a combination of compatible chimney components, obtained or specified from one manufacturing source with product responsibility for the whole system chimney. NOTE – This document does not cover soot fire resistance chimneys.