Please choose at least one filter
Time limit for review from
Characteristic values for welded thermoplastics constructions - Determination of allowable stresses and moduli for design of thermoplastics equipment
Plastics - Determination of the gas transmission rate of films and thin sheets under atmospheric pressure - Manometric method
Rubber- or plastics-coated fabrics - Determination of resistance to damage by flexing
Plastics - Film and sheeting - Determination of the coefficients of friction
Plastics – Generic identification and marking of plastics products
Plastics - Film and sheeting - Determination of dimensional change on heating
Plastics – Polytetrafluoroethylene (PTFE) semi-finished products – Part 1: Requirements and designation (ISO 13000-1:2021)
Plastics – Polytetrafluoroethylene (PTFE) semi-finished products – Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2021)
Rubber- or plactics-coated fabrics - Determination of blocking resistance
Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheets 4 to 6: Requirements for polyimide films used for electrical insulation
Rubber - Tolerances for products - Part 1: Dimensional tolerances
Plastics – Polytetrafluoroethylene (PTFE) semi-finished products – Part 1: Requirements and designation
Plastics – Polytetrafluoroethylene (PTFE) semi-finished products – Part 2: Preparation of test specimens and determination of properties
Rubber – Tolerances for products – Part 2: Geometrical tolerances
Rubber – Compatibility between hydraulic fluids and standard elastomeric materials
Road vehicles – Tests for rigid plastic safety glazing materials
Plastics moulded parts – Tolerances and acceptance conditions
Rubber and rubber products - Environmental aspects - General guidelines for their inclusion in standards
Standard Practice for Application of Electrical Discharge Surface Treatment (Activation) of Plastics for Adhesive Bonding
Standard Specification for Sprayed Slurries, Foams and Indigenous Materials Used As Alternative Daily Cover for Municipal Solid Waste Landfills
Standard Specification for Finished Parts Made from Polyimide Resin
Standard Terminology Relating to Reinforced Plastic Pultruded Products
Standard Symbols for Dimensions of Plastic Pipe Fittings
Standard Specification for Parts Machined from Polychlorotrifluoroethylene (PCTFE) and Intended for General Use
Standard Test Methods for Use of Emulsion Polymers in Floor Polishes
Standard Practice for Confirmation of 20–mm (50–W) and 125–mm (500–W) Test Flames for Small-Scale Burning Tests on Plastic Materials
Standard Test Method for Specular Gloss
Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Dual Cantilever Beam)
Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
Standard Classification System and Basis for Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC)
Standard Specification for Polyethylene-Based Structural-Grade Plastic Lumber for Outdoor Applications
Standard Test Method for Predicting Heat Buildup in PVC Building Products
Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
Standard Test Methods for Compressive and Flexural Creep and Creep-Rupture of Plastic Lumber and Shapes
Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes
Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe
Standard Test Method for Compressive Properties of Plastic Lumber and Shapes
Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastic Lumber and Related Products
Standard Test Method for Bulk Density And Specific Gravity of Plastic Lumber and Shapes by Displacement
Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers
Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM)
Standard Test Method for Determination of Oxygen Gas Transmission Rate, Permeability and Permeance at Controlled Relative Humidity Through Barrier Materials Using a Coulometric Detector
Standard Test Method for Impact Resistance of Poly(Vinyl Chloride) (PVC) Rigid Profiles by Means of a Falling Weight
Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
Standard Practice for Coding Plastic Manufactured Articles for Resin Identification
Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-On-Ring Configuration
Plastics - Compression moulding test specimens of thermoplastic materials
Plastic mouldings. Tolerances and acceptance conditions of dimensions
Light transmitting profiled plastic sheeting for single skin roofing - Part 3: Specific requirements and test methods for sheets of polyvinyl chloride (PVC)
Rubber hoses for agricultural spraying
Flexible sheets for waterpoofing - Plastic and rubber sheets for roof waterproofing - methods for exposure to liquid chemicals, including water
Rubber hose and hose assemblies for transferring anhydrous ammonia - Specification
Plastics - Generic identification and marking of plastics products
Surfaces for sports areas - Procedure for the preparation of synthetic turf and textile test pieces
Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation
Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties
Adhesives for leather and footwear materials - Preparation of bonded test pieces by moulding-on processes
Extruded sheets of impact-modified polystyrene (PS-I) - Requirements and test methods
Extruded sheets of polyethylen (PE-HD) - Requirements and test methods.
Extruded sheets of polypropylene (PP) - Requirements and test methods
Plastics - Development and use of intermediate-scale fire tests for plastics products - Part 1: General guidance
Specification for pressure-sensitive adhesive tapes for electrical purposes - Part 2: Methods of test
You must be logged in to sign up for monitoring
You must be logged in to sign up for subscription
There is a problem adding monitoring - please try again later
There is a problem adding the subscription - please try again later
Du overvåger allerede dette emne
Du overvåger allerede denne standard
Er du sikker på at du vil overvåge dette emne?
Er du sikker på at du vil overvåge denne standard?
Du abonnerer allerede dette emne
Du abonnerer allerede denne standard
Er du sikker på at du vil abonnere på dette emne?
Er du sikker på at du vil abonnere på denne standard?
Du abonnerer nu på dette emne!
Du abonnerer nu på denne standard!
Activation of your subscription failed - please try again later or contact us
Du overvåger nu dette emne!
Du overvåger nu denne standard!
Activation of monitoring failed - please try again later or contact us
Are you sure you want to unsubscribe monitoring?
Are you sure you want to unsubscribe?
It was not possible to unsubscribe - please try again later or contact the Danish Standard
Please make sure you are logged in
Please choose number of devices you want to open the document on
The printed version is available at half price when you buy the electronic version
It is not possible to buy in the shop - please contact us